Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you are reading around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Density: 4mm

REMARKS:
These bearings are utilized to support the Primary Clutch (one needed).

Regularly gotten with the product that you are presently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Regularly gotten with the product that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This is a fantastic addition to the product presently being gone over.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon building and construction

INCLUDES:
Two Front bearing (hub) providers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

This is a fantastic addition to the product presently being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

You will love this thing if you have the thing earlier mentioned.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on automobile

This product compliments the main item below.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits numerous Traxxas
automobiles. .
Includes: 1 gear only

You will love this thing if you have the thing earlier mentioned.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon building and construction

INCLUDES:
Two rear bearing (hub) providers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

You will love this thing if you have the thing earlier mentioned.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the automobile

REMARKS:
For primary differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037