Traxxas 30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on vehicle

You will certainly like this thing if you have the thing earlier pointed out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This product compliments the main item here.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive gear that fits a number of Traxxas
vehicles. .
Consists of: 1 gear just

Many others have actually gotten this product in addition to the product that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

Many others have actually gotten this product in addition to the product that you are presently reading about.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

NEEDS:
Installation on the vehicle

COMMENTS:
For primary differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

Here is a wonderful product that lots of others have actually bought at the very same time.

Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Equipment from Traxxas
for the Outlaw, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Guidelines

Requires: Installation on the vehicle

Want an additional wonderful product to enhance the above stated product?

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Here is an additional product that compliments the product being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

Want an additional wonderful product to enhance the above stated product?

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL variation of both the Stampede
and Rustler.

You will certainly like this thing if you have the thing earlier pointed out.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
Two front axles

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.