Traxxas Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Numerous others have actually bought this item along with the item that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Numerous others have actually bought this item along with the item that you are presently reviewing.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

Here is a fantastic item that several others have actually purchased the very same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

The listed below item additionally sets actually well with the item being reviewed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This item compliments the main item right here.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Setup on vehicle

You will like this thing if you have the thing above mentioned.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits numerous Traxxas
automobiles. .
Includes: 1 equipment just

The listed below item additionally sets actually well with the item being reviewed.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

CONSISTS OF:
2 front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, use
    TRAC2536.

Numerous others have actually bought this item along with the item that you are presently reviewing.

Metal Washers/12

These are 3x6mm Washers from Traxxas.

FEATURES:
Metal building

CONSISTS OF:
(12) Washers

SPECIFICATIONS:
Size: 3x6mm

Numerous others have actually bought this item along with the item that you are presently reviewing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on vehicle

This is a great addition to the item presently being reviewed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL variation of both the Stampede
and Rustler.