RPM Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
Two Front bearing (center) providers
Two RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

Often purchased with the item that you are presently reviewing.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building and construction, black in color
Stamped right and left to insure correct setup

CONSISTS OF:
Two RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and steering knuckles

Here is a terrific item that numerous others have bought at the very same time.

Heat-Treated, Carbon Steel Front King-Pins, For Traxxas Slash /

This is a pair of ST Racing Principles Polished Front King Pins
for the 1/10 scale 2WD Traxxas Slash.

FEATURES:
CNC machined, heat dealt with and polished steel building and construction

CONSISTS OF:
Left and Right King Pins for front suspension

This item compliments the above discussed item.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles fit into these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
Two rear bearing (center) providers
Two RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

This item compliments the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item compliments the main item right here.

Rear A-Arms, For Traxxas Slash, Black

    These are the RPM Strong Rear A-Arms for the
2WD Traxxas Slash Short Course Racing Truck.

FEATURES:
Nylon building and construction
Black in color
Very resilient

CONSISTS OF:
Two Heavy Task Rear A-Arms

REQUIRES:
Installation on the car

SPECIFICATIONS:
Length: 95mm (3.7")
Width: 47mm (1.85")
Height: 10.5mm (0.41")

COMMENTS:
Also available in Blue RPMC8472

This item compliments the above discussed item.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FUNCTIONS:
Made of stainless-steel
This is used to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electric
(not Nitro) Rustler
Also called the vertical kingpin

CONSISTS OF:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

The listed below item additionally sets actually well with the item being discussed.

Front Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the optional RPM Front Shock Tower for the
Traxxas E-Stampede, E- Rustler, Bandit & Nitro Stampede.

FEATURES:
Plastic building and construction
Black in color

CONSISTS OF:
One Front Shock Tower for the Traxxas E-Stampede, E-Rustler, Bandit
    and Nitro Stampede

REQUIRES:
Installation on the car

SPECIFICATIONS:
Width: 3.26" (83mm)
Height: 2.91" (74mm)
Thickness: .27" (7mm)