Traxxas Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on vehicle

Get this product to improve the one you read around.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on vehicle

The listed below product additionally sets really well with the product being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will enjoy this product if you have the product just above mentioned.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Numerous others have actually gotten this product in addition to the product that you are currently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Want another wonderful product to compliment the above stated product?

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

REQUIRES:
Setup on the vehicle

REMARKS:
For primary differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037

This product is often gotten with the above stated product.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler gear

REQUIRES:
Setup on vehicle

The listed below product additionally sets really well with the product being gone over.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

This product praises the above gone over product.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL variation of both the Stampede
and Rustler.

This is a great enhancement to the product currently being gone over.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the vehicle