Align 2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Direction::
Max Continuous Discharge: 30C. Typical operating temperature is approx. 40-65?C(within 80% of ranked discharge). Max. temperature: 80?C.
Recommend to release the battery within 80% of ranked discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and effectiveness will reduce due to high current, high temperature and over-discharge)

KEEP IN MIND::
When utilizing high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Releasing capacity can't exceed 80% of the max capacity after complete charging to guarantee an excellent cycle performance.Recommend to complete charge a brand name brand-new battery before utilizing and just release the battery 50% for very first 5 times making an excellent effectiveness of the battery. Please make it a practice to always count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping utilizing can not reduce than 3.4V). Do not utilize the battery at insufficient of voltage.

Do not expose batteries to sunshine or shop/ charge batteries at the temperature up to 35℃ in a airtight vehicle. The environment high temperature could trigger the damage or the risk of burst. If the battery ends up being hot while high current discharging or flying, please do not charge the battery immediately. Wait to cool down(about 20 minutes), then inspect to recharge. If versus follow the initial factory utilizing guidelines, possibly trigger the battery to inflate or any hazardous mishap happens.
Do not leave the charger is running unattended as it may trigger a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Dimension:47x21.5x12mm
Weight:15g

This is a wonderful addition to the product currently being discussed.

T-Rex 150 DFC Combo BTF Twin BL Motor, 2S 7.4V 250Mah

Align's tiniest and most small 3D helicopter T-Rex 150 DFC, carries the very same exceptional pedigree and design concept that originated from the successful T-Rex line of helicopters. Including strong power, exceptional flight control stability, and equipped with high end components, far going beyond other helicopters currently on the market.

Twin brushless motor design, coupled with 2s 7.4v 250mah battery, developing power that will go beyond all your expectations. Metal DFC primary rotor head assembly including high end visual and exceptional flight efficiency; in addition, an integrated control system with specially optimized 3-axis gyro, receiver, electronic speed controller, and 4g servos. All these make it possible for the T-Rex 150 DFC to posses the very same stability, exceptional agility, and tail holding effectiveness as the larger helicopters.

T-Rex 150 features built in Futaba S-FHSS 2.4Ghz system, and support making use of Spektrum DSM2/DSMX / JR DSM2/DSMJ/DMSS satellite receivers. To get the T-Rex 150 airborne, everythings required is inputting of parameters noted in handbook into your transmitter, and binding of your transmitter.

Miniature size, control accuracy that appears like the larger helicopters, enables you to take pleasure in flying inside a confined space. Beginners can even enjoy this with ease by simply denying the speed dial. The ingenious development T-Rex 150 will bring you a brand-new dimension of flying enjoyment.

Specification:
Length: 255mm
Height: 80mm
Main Blade Length: 120mm
Main Rotor Size: 271mm
Tail Rotor Size: 41mm
Motor Pinion Gear: 10T
Main Drive Gear: 78T
Drive Gear Ratio: 1:7.8
Weight (w/o Battery): 53g

Accessories:
T-REX 150 DFC Set x 1
Main Blades x 2set
Tail Blades x 1
150M Main Motor x 1
150M Tail Motor x 1
S150 micro Servo x 2
DS155 micro Servo x 1
Blnd Plug x 1
Remote Extension x 1
7.5V Li-Po 250mAh Li-Polymer Battery x 1

Radio transmitter and electronic equipment needed for assembly:
1.ALIGN T6 or Futaba S-FHSS 2.4G Transmitter or JR DSM2/DSMJ/DMSS、Spektrum DSM2/DSMX 2.4GHz Transmitter