Align 150 Spare Parts Pack

Use for T-REX 150.

Specs:
Socket button head screw x 5(#0-80x6.2mm)
Washer x 4(Φ2xΦ3.6x0.2mm)
150 Head Damper x 2(Φ2xΦ4x1.3mm)
Socket Button Head Screw x 5(#0-80x3mm)
100 Spacer x 4(Φ1.6xΦ3.2x0.2mm)
Socket button head screw x 4(#0-80x8mm)
Φ2.1 Linkage ball A x 5(Φ2.1x4.28mm)
Socket button head screw x 2(M2x4mm)
Cross screw x 2(T1.5x4mm)
150 Ball Link A x 2(Φ2.1x13.3x2mm)
150 Ball Link B x 4(Φ2.1x10.5x2mm)
150 Landing Skid Spacer x 4(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 5(T1.5x3mm)
Socket button head self tapping screw x 5(T1.5x4mm)
Motor Pinion Gear 10T x 1
100 Canopy nut x 4
Strap x 5(1.6x71mm)

Want one more fantastic product to compliment the above pointed out product?

150 Main Shaft

Use for T-REX 150.

Specs:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

This product is often gotten with the above pointed out product.

DS150 Digital Servo

Suitable for T-Rex 150

Directions:
4g digital micro servos are special design for T-REX 150 DFC, includes to increase micro helicopter control speed and precision, let the micro/indoor helicopter has same flight efficiency as large/outdoor helicopter.

Specs:
Stall torque:0.8kg．cm(5V)
Motion speed:0.06 sec/60?(5V)
Rating voltage:DC 4.8-6V
Measurement:19.8x8.4x23.3mm
Weight:4.3g
1520μs conventional band

Accessories:
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Want one more fantastic product to compliment the above pointed out product?

100 Main Drive Gear

This is a replacement Align Main Drive Gear, and is intended for usage with the Align T-Rex 100 helicopter.



This is a fantastic enhancement to the product presently being talked about.

150 Landing Skid

Use for T-REX 150.

Specs:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Want one more fantastic product to compliment the above pointed out product?

2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Guideline::
Max Continuous Discharge: 30C. Normal operating temperature is approx. 40-65?C(within 80% of ranked discharge). Max. temperature: 80?C.
Recommend to release the battery within 80% of ranked discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and performance will minimize due to high existing, high temperature and over-discharge)

KEEP IN MIND::
When utilizing high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Releasing capacity can't exceed 80% of the max capacity after complete charging to make sure an excellent cycle performance.Recommend to complete charge a brand name brand-new battery prior to utilizing and only release the battery 50% for first 5 times to make an excellent performance of the battery. Please make it a habit to always count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping utilizing can not reduce than 3.4V). Do not use the battery at inadequate of voltage.

Do not expose batteries to sunshine or shop/ charge batteries at the temperature approximately 35℃ in a airtight car. The environment high temperature might cause the damage or the risk of burst. If the battery ends up being hot while high existing discharging or flying, please do not charge the battery instantly. Wait to cool off(about 20 minutes), then check to recharge. If versus follow the original factory utilizing rules, potentially cause the battery to pump up or any harmful accident takes place.
Do not leave the battery charger is running unattended as it might cause a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Measurement:47x21.5x12mm
Weight:15g