Align 2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Instruction::
Max Continuous Discharge: 30C. Normal operating temperature level is approx. 40-65?C(within 80% of rated discharge). Max. temperature level: 80?C.
Recommend to release the battery within 80% of rated discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and efficiency will lower due to high current, high temperature level and over-discharge)

KEEP IN MIND::
When utilizing high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature level. Releasing capacity cannot go beyond 80% of limit capacity after complete charging to ensure a great cycle performance.Recommend to complete charge a brand new battery prior to utilizing and only release the battery 50% for first 5 times making a great efficiency of the battery. Please make it a routine to always count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping utilizing can not decrease than 3.4V). Do not utilize the battery at insufficient of voltage.

Do not expose batteries to sunlight or shop/ charge batteries at the temperature level up to 35℃ in a airtight car. The environment high temperature level could cause the damage or the danger of burst. If the battery ends up being hot while high current discharging or flying, please do not charge the battery instantly. Wait to cool down(about 20 mins), then check to recharge. If against follow the initial factory utilizing rules, perhaps cause the battery to pump up or any dangerous accident takes place.
Do not leave the charger is operating ignored as it may cause a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Measurement:47x21.5x12mm
Weight:15g

This is a wonderful addition to the thing presently being reviewed.

T-Rex 150 DFC Combo BTF Twin BL Motor, 2S 7.4V 250Mah

Align's smallest and most petite 3D helicopter T-Rex 150 DFC, brings the exact same remarkable pedigree and design principle that stemmed from the successful T-Rex line of helicopters. Including strong power, remarkable flight control stability, and equipped with high end parts, far going beyond any other helicopters currently on the market.

Twin brushless motor design, coupled with 2s 7.4v 250mah battery, developing power that will exceed all your expectations. Metal DFC primary rotor head assembly featuring high end visual and remarkable flight efficiency; in addition, an integrated control system with specially optimized 3-axis gyro, receiver, electronic speed controller, and 4g servos. All these allow the T-Rex 150 DFC to posses the exact same stability, remarkable dexterity, and tail holding efficiency as the larger helicopters.

T-Rex 150 functions integrated in Futaba S-FHSS 2.4Ghz system, and support the use of Spektrum DSM2/DSMX / JR DSM2/DSMJ/DMSS satellite receivers. To get the T-Rex 150 airborne, everythings required is inputting of specifications noted in manual into your transmitter, and binding of your transmitter.

Miniature size, control precision that resembles the larger helicopters, enables you to delight in flying inside a restricted space. Beginners can even enjoy this with ease by just declining the speed dial. The ingenious breakthrough T-Rex 150 will bring you a brand-new dimension of flying enjoyment.

Specification:
Length: 255mm
Height: 80mm
Main Blade Length: 120mm
Main Rotor Size: 271mm
Tail Rotor Size: 41mm
Motor Pinion Gear: 10T
Main Drive Gear: 78T
Drive Gear Ratio: 1:7.8
Weight (w/o Battery): 53g

Devices:
T-REX 150 DFC Set x 1
Main Blades x 2set
Tail Blades x 1
150M Main Motor x 1
150M Tail Motor x 1
S150 micro Servo x 2
DS155 micro Servo x 1
Blnd Plug x 1
Remote Extension x 1
7.5V Li-Po 250mAh Li-Polymer Battery x 1

Radio transmitter and electronic devices required for assembly:
1.ALIGN T6 or Futaba S-FHSS 2.4G Transmitter or JR DSM2/DSMJ/DMSS、Spektrum DSM2/DSMX 2.4GHz Transmitter