Align 150 Receiver Double sided tape

Ideal for the 150 MRS 3 in 1 Controller.

Specifications:
150 Receiver Double sided tape x 4(26x18x2.5mm)

Want one more terrific item to compliment the above mentioned item?

150 Tail Boom Red

Use for T-REX 150.

Specifications:
150 Tail boom-Red x 2(3.5x3.5x140mm)
150 Tail motor install x 2
Socket button head self screw x 2(T1.5x3mm)
Socket button head screw x 2(#0-80x3mm)

Want one more terrific item to compliment the above mentioned item?

150MT Tail Motor Assembly

Use for T-REX 150.

Specifications:
KV value: 8000KV
Input voltage: 2S
Stator Arms: 9
Magnet Poles: 6
Measurement: 1.4x13.2x18.1mm
Weight: 3.3g

Accessories:
150M Tail Motor x 1
150 Motor Wire Socket x 1
Strap x 2(1.6x71mm)
Socket Button Head Screw x 1(#0-80x3mm)

This is a superb enhancement to the item presently being discussed.

DS150/155 Servo Gear Set

Use for ALIGN DS150/155 Servo.

Specifications:
DS150/155 gear G1x1
DS150/155 gear G2x1
DS150/155 gear G3x1
DS150/155 gear G4x1
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Numerous others have actually gotten this item in addition to the item that you are presently checking out.

150 Landing Skid

Use for T-REX 150.

Specifications:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Numerous others have actually gotten this item in addition to the item that you are presently checking out.

150 Main Shaft

Use for T-REX 150.

Specifications:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

Here is a terrific item that lots of others have actually bought at the very same time.

DS150 Digital Servo

Ideal for T-Rex 150

Directions:
4g digital micro servos are special design for T-REX 150 DFC, includes to increase micro helicopter control speed and accuracy, let the micro/indoor helicopter has same flight performance as large/outdoor helicopter.

Specifications:
Stall torque:0.8kg．cm(5V)
Motion speed:0.06 sec/60?(5V)
Score voltage:DC 4.8-6V
Measurement:19.8x8.4x23.3mm
Weight:4.3g
1520μs basic band

Accessories:
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

The listed below item also pairs really well with the item being discussed.

2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Guideline::
Max Constant Discharge: 30C. Regular operating temperature level is approx. 40-65?C(within 80% of rated discharge). Max. temperature level: 80?C.
Recommend to discharge the battery within 80% of rated discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and efficiency will decrease due to high current, high temperature level and over-discharge)

NOTE::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature level. Releasing capacity cannot go beyond 80% of the max capacity after full charging to make sure a good cycle performance.Recommend to full charge a brand name brand-new battery prior to using and only discharge the battery 50% for first 5 times to make a good efficiency of the battery. Please make it a practice to always count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping using can not decrease than 3.4V). Do not use the battery at insufficient of voltage.

Do not expose batteries to sunshine or store/ charge batteries at the temperature level up to 35℃ in a airtight car. The environment high temperature level could trigger the damage or the danger of burst. If the battery ends up being hot while high current discharging or flying, please do not charge the battery right away. Wait to cool down(about 20 mins), then examine to charge. If versus follow the initial factory using rules, possibly trigger the battery to inflate or any harmful accident occurs.
Do not leave the battery charger is operating unattended as it might trigger a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Measurement:47x21.5x12mm
Weight:15g