Align 150MT Tail Motor Assembly

Usage for T-REX 150.

Requirements:
KV value: 8000KV
Input voltage: 2S
Stator Arms: 9
Magnet Poles: 6
Dimension: 1.4x13.2x18.1mm
Weight: 3.3g

Devices:
150M Tail Motor x 1
150 Motor Wire Socket x 1
Strap x 2(1.6x71mm)
Socket Button Head Screw x 1(#0-80x3mm)

The below thing likewise sets really well with the thing being discussed.

150 Motor Plug & Pin Set

Devices:
150 Pin Set x 3 pcs
150 Motor Plug x 9 pcs
Φ0.8 Heat diminish tube-Black(4mm) x 3
Φ0.8 Heat diminish tube-Red(4mm) x 3
Φ0.8 Heat diminish tube-Blue(4mm) x 3

Get this thing to improve the one you read around.

150 Landing Skid

Usage for T-REX 150.

Requirements:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Here is one more thing that praises the thing being discussed.

150 Receiver Double sided tape

Suitable for the 150 MRS 3 in 1 Controller.

Requirements:
150 Receiver Double sided tape x 4(26x18x2.5mm)

This thing praises the main item here.

150 Main Shaft

Usage for T-REX 150.

Requirements:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

This thing praises the above discussed thing.

150 Feathering Shaft

Usage for T-REX 150.

Requirements:
150 Feathering shaft x 3(Φ2x16.5mm)
Socket Button Head Screw x 6(#0-80x3mm)
100 Spacer x 6(Φ1.6x3.2x0.2mm)

Numerous others have actually purchased this thing in addition to the thing that you are presently checking out.

DS150 Digital Servo

Suitable for T-Rex 150

Guidelines:
4g digital micro servos are special design for T-REX 150 DFC, includes to increase micro helicopter control speed and precision, let the micro/indoor helicopter has exact same flight efficiency as large/outdoor helicopter.

Requirements:
Stall torque:0.8kg．cm(5V)
Movement speed:0.06 sec/60?(5V)
Score voltage:DC 4.8-6V
Dimension:19.8x8.4x23.3mm
Weight:4.3g
1520μs conventional band

Devices:
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Want one more terrific thing to enhance the above stated thing?

150 Tail Boom Red

Usage for T-REX 150.

Requirements:
150 Tail boom-Red x 2(3.5x3.5x140mm)
150 Tail motor install x 2
Socket button head self screw x 2(T1.5x3mm)
Socket button head screw x 2(#0-80x3mm)

You will certainly enjoy this thing if you have the thing above stated.

2S1P 7.4V 250mAh/30C

Usage for T-REX 150.

Guideline::
Max Continuous Discharge: 30C. Regular operating temperature level is approx. 40-65?C(within 80% of ranked discharge). Max. temperature level: 80?C.
Recommend to release the battery within 80% of ranked discharge, keep 95% capability when over 100 cycles, keep 90% capability when over 150 cycles.(The cycle life and efficiency will minimize due to high existing, high temperature level and over-discharge)

KEEP IN MIND::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature level. Discharging capability can't exceed 80% of limit capability after complete charging to ensure a great cycle performance.Recommend to complete charge a brand name brand-new battery prior to using and only release the battery 50% for very first 5 times to make a great efficiency of the battery. Please make it a habit to constantly count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping using can not reduce than 3.4V). Do not use the battery at insufficient of voltage.

Do not expose batteries to sunlight or store/ charge batteries at the temperature level up to 35℃ in a airtight car. The environment high temperature level could trigger the damage or the threat of burst. If the battery ends up being hot while high existing discharging or flying, please do not charge the battery immediately. Wait to cool off(about 20 minutes), then examine to recharge. If against follow the original factory using guidelines, perhaps trigger the battery to inflate or any hazardous accident occurs.
Do not leave the charger is operating ignored as it might trigger a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Dimension:47x21.5x12mm
Weight:15g