Align 150 Feathering Shaft

Use for T-REX 150.

Requirements:
150 Feathering shaft x 3(Φ2x16.5mm)
Socket Button Head Screw x 6(#0-80x3mm)
100 Spacer x 6(Φ1.6x3.2x0.2mm)

This item compliments the main item right here.

150 Main Shaft

Use for T-REX 150.

Requirements:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

Get this item to improve the one you are reading about.

150 Landing Skid

Use for T-REX 150.

Requirements:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Several others have acquired this item along with the item that you are currently reviewing.

DS150/155 Servo Gear Set

Use for ALIGN DS150/155 Servo.

Requirements:
DS150/155 gear G1x1
DS150/155 gear G2x1
DS150/155 gear G3x1
DS150/155 gear G4x1
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Here is a excellent item that many others have purchased the exact same time.

78T Main Drive Gear

Use for T-REX 100S/100X/150.

Requirements:
Main Drive Gear(78T) x 2

This item is regularly acquired with the above discussed item.

DS150 Digital Servo

Appropriate for T-Rex 150

Instructions:
4g digital micro servos are special design for T-REX 150 DFC, features to increase micro helicopter control speed and accuracy, let the micro/indoor helicopter has very same flight performance as large/outdoor helicopter.

Requirements:
Stall torque:0.8kg．cm(5V)
Movement speed:0.06 sec/60?(5V)
Score voltage:DC 4.8-6V
Measurement:19.8x8.4x23.3mm
Weight:4.3g
1520μs conventional band

Accessories:
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

This item compliments the main item right here.

2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Direction::
Max Continuous Discharge: 30C. Typical operating temperature is approx. 40-65?C(within 80% of rated discharge). Max. temperature: 80?C.
Recommend to release the battery within 80% of rated discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and efficiency will lower due to high current, high temperature and over-discharge)

NOTE::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Releasing capacity cannot exceed 80% of limit capacity after complete charging to ensure an excellent cycle performance.Recommend to complete charge a brand name new battery prior to using and just release the battery 50% for very first 5 times to make an excellent efficiency of the battery. Please make it a routine to constantly count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping using can not decrease than 3.4V). Do not utilize the battery at insufficient of voltage.

Do not expose batteries to sunlight or store/ charge batteries at the temperature up to 35℃ in a airtight automobile. The environment high temperature could trigger the damage or the risk of burst. If the battery becomes hot while high current discharging or flying, please do not charge the battery immediately. Wait to cool down(about 20 minutes), then examine to recharge. If against follow the initial factory using rules, perhaps trigger the battery to inflate or any hazardous mishap happens.
Do not leave the charger is operating unattended as it might trigger a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Measurement:47x21.5x12mm
Weight:15g