Align DS150/155 Servo Gear Set

Use for ALIGN DS150/155 Servo.

Requirements:
DS150/155 gear G1x1
DS150/155 gear G2x1
DS150/155 gear G3x1
DS150/155 gear G4x1
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Numerous others have actually acquired this product along with the product that you are currently checking out.

150 Main Shaft

Use for T-REX 150.

Requirements:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

The listed below product also pairs really well with the product being talked about.

150 Feathering Shaft

Use for T-REX 150.

Requirements:
150 Feathering shaft x 3(Φ2x16.5mm)
Socket Button Head Screw x 6(#0-80x3mm)
100 Spacer x 6(Φ1.6x3.2x0.2mm)

Regularly acquired with the product that you are currently checking out.

DS150 Digital Servo

Appropriate for T-Rex 150

Guidelines:
4g digital micro servos are unique design for T-REX 150 DFC, includes to increase micro helicopter control speed and precision, let the micro/indoor helicopter has exact same flight performance as large/outdoor helicopter.

Requirements:
Stall torque:0.8kg．cm(5V)
Motion speed:0.06 sec/60?(5V)
Score voltage:DC 4.8-6V
Measurement:19.8x8.4x23.3mm
Weight:4.3g
1520μs conventional band

Accessories:
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Get this product to enhance the one you are reading about.

150 Landing Skid

Use for T-REX 150.

Requirements:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Below is a wonderful product that numerous others have actually purchased the very same time.

78T Main Drive Gear

Use for T-REX 100S/100X/150.

Requirements:
Main Drive Gear(78T) x 2

Regularly acquired with the product that you are currently checking out.

2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Instruction::
Max Continuous Discharge: 30C. Normal operating temperature is approx. 40-65?C(within 80% of ranked discharge). Max. temperature: 80?C.
Recommend to release the battery within 80% of ranked discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and effectiveness will minimize due to high existing, high temperature and over-discharge)

KEEP IN MIND::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Releasing capacity cannot go beyond 80% of the max capacity after full charging to make sure a good cycle performance.Recommend to full charge a brand name new battery prior to using and only release the battery 50% for first 5 times to make a good effectiveness of the battery. Please make it a habit to constantly count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping using can not reduce than 3.4V). Do not use the battery at inadequate of voltage.

Do not expose batteries to sunshine or shop/ charge batteries at the temperature up to 35℃ in a airtight vehicle. The environment high temperature might cause the damage or the risk of burst. If the battery ends up being hot while high existing discharging or flying, please do not charge the battery immediately. Wait to cool down(about 20 minutes), then examine to charge. If against follow the initial factory using guidelines, potentially cause the battery to inflate or any hazardous accident takes place.
Do not leave the charger is operating ignored as it may cause a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Measurement:47x21.5x12mm
Weight:15g