Align 20 Tail Blade

Use for T-REX 150.

Requirements:
Tail Blade x 4
Length:41.35 mm
Weight:Approx 0.21g/single

Here is a wonderful item that many others have actually bought at the very same time.

150 Vertical Stabilizer

Use for T-REX 150.

Requirements:
Vertical Stabilizer x 2

Here is a wonderful item that many others have actually bought at the very same time.

150 Tail Boom

Use for T-REX 150.

Requirements:
150 tail boom x 2(3.5x3.5x140mm)
150 Tail motor install x 2
Socket button head self screw x 2(T1.5x3mm)
Socket button head screw x 2(#0-80x3mm)

This item is regularly gotten with the above pointed out item.

2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Guideline::
Max Continuous Discharge: 30C. Normal operating temperature is approx. 40-65?C(within 80% of ranked discharge). Max. temperature: 80?C.
Recommend to discharge the battery within 80% of ranked discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and efficiency will minimize due to high present, heat and over-discharge)

KEEP IN MIND::
When utilizing high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Releasing capacity can't surpass 80% of limit capacity after complete crediting guarantee an excellent cycle performance.Recommend to complete charge a brand brand-new battery prior to utilizing and just discharge the battery 50% for first 5 times to make an excellent efficiency of the battery. Please make it a habit to constantly count time for flight, or please set a low voltage security on ESC (Cell voltage after stopping utilizing can not reduce than 3.4V). Do not use the battery at insufficient of voltage.

Do not expose batteries to sunlight or shop/ charge batteries at the temperature approximately 35℃ in a airtight automobile. The environment heat could cause the damage or the danger of burst. If the battery ends up being hot while high present discharging or flying, please do not charge the battery immediately. Wait to cool off(about 20 minutes), then check to charge. If versus follow the initial factory utilizing rules, possibly cause the battery to inflate or any hazardous accident happens.
Do not leave the charger is running ignored as it might cause a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Dimension:47x21.5x12mm
Weight:15g

This item is regularly gotten with the above pointed out item.

120 Main Blades-Black

Use for T-REX 150.

Requirements:
Forming: In proportion wing
Length:120 mm
Weight:Approx 5.8g/set

Accessories:
Main Blades x 2 set
Main blade Decal x 1 set

This item praises the above discussed item.

150 Main Shaft

Use for T-REX 150.

Requirements:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

You will certainly love this product if you have the product earlier stated.

150 Feathering Shaft

Use for T-REX 150.

Requirements:
150 Feathering shaft x 3(Φ2x16.5mm)
Socket Button Head Screw x 6(#0-80x3mm)
100 Spacer x 6(Φ1.6x3.2x0.2mm)

Get this item to improve the one you are reading around.

150 Main Frame

Use for T-REX 150.

Requirements:
150 Main Frame x 1
150 Servo upper case x 1
Bearing H63 x 2(Φ3xΦ6x2mm)
150 Receiver install x 1
Cross screwx 2(T1.5x4mm)
Socket button head self tapping screw x 1(T1.5x4mm)
Socket button head self tapping screw x 1(T1.5x3mm)