Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Completely assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Attaches to the differential with one screw pin
Works on the front or back, right or left of vehicle

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

REQUIRES:
Installing on chassis

This item praises the main item here.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto vehicle

Many others have actually purchased this item in addition to the item that you are presently reading about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Steel Building
Blue Rubber Sealed

CONSISTS OF:
Two 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

REQUIRES:
Assembly onto Vehicle

SPECS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Density: 4mm (0.15")

COMMENTS:
These are for the Within the Wheel Hubs, the Truck Needs
4 Total of these Bearings.

The below item additionally pairs truly well with the item being discussed.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This plan consists of a part of the telescoping drive shafts.

FEATURES:
Black plastic building
Blue rubber shaft boots

CONSISTS OF:
Two half shaft assemblies

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Often purchased with the item that you are presently reading about.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FEATURES:
Stainless Steel bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECS:
Inside size: 6mm (0.24")
Outdoors size: 13mm (0.51")
Width: 5mm (0.20")

Get this item to improve the one you read about.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle providers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes broken axle providers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle providers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, setting up two 12x18mm ball
    bearings, stub axles, and pillow balls.

Here is a excellent item that numerous others have actually purchased the exact same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Building
Black in Color
Permits for Oversized Bearing utilize

CONSISTS OF:
One Left Axle Carrier
One Right Axle Carrier
4 Dust Boot Retainers
Two Bearing Spacers

REQUIRES:
Setup

Often purchased with the item that you are presently reading about.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Safeguards the Vehicle.

FEATURES:
Lexan building
Pre-painted graphics
Body mount holes pre-drilled
Pre-cut
Protective movie covers outside of body after surface and is removed
    after conclusion of paint task

CONSISTS OF:
One painted graphics E-Revo Body
One decal set

REQUIRES:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

REMARK:
Graphics are pre-painted. Needs paint and last
decal application.