Traxxas U-Joints, Driveshaft Revo

These are the Drive Shaft Joints for the Traxxas Revo.

FEATURES:
Steel universal joint set

CONSISTS OF:
Four Steel Universal blocks
Four Steel Universal pins
Two black steel set pins
Four steel hinge pins
Four steel bearing pins
Eight 1.4mm e-clips

NEEDS:
Installing on Traxxas Revo

Below is another item that compliments the item being gone over.

Yokes Diff/Tranny

These are the Diff and Trans Drive Yokes for the Traxxas T-Maxx 3.3. TRAC78**

FEATURES:
Black plastic construction

CONSISTS OF:
Two drive yokes
Two 4x15mm Yoke pins

NEEDS:
T-Maxx 3.3

SPECIFICATIONS:
Length: 15/16" (23mm)
Size: 3/4" (17mm)

Want another fantastic item to enhance the above mentioned item?

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Completely assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping areas from dirt
Attaches to the differential with one screw pin
Works on the front or rear, right or left of car

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

NEEDS:
Installing on chassis

This item compliments the main item right here.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FEATURES:
Stainless-steel bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside diameter: 6mm (0.24")
Outdoors diameter: 13mm (0.51")
Width: 5mm (0.20")

This item compliments the above gone over item.

Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

CONSISTS OF:
Four Blue Rubber Pivot Ball Boots
Four Black Dust Boot Retainer
Four Blue Notched Dust Boot Retainer
Four Blue Rubber Boot Plugs
Four nylon Pivot Ball Retainers
Guideline sheet

NEEDS:
Two plans had to finish truck

Several others have bought this item together with the item that you are currently reviewing.

Center Half Shafts E-Revo

This is the Center Half Shaft Set for the Traxxas E-Revo

FEATURES:
Plastic construction, black in color

CONSISTS OF:
Center half shafts (3 internal splined and 2 external splined)

NEEDS:
Installation on the car

SPECIFICATIONS:
Size: 17.2mm (0.68")

Get this item to boost the one you are reading around.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless-steel Construction
Blue Rubber Sealed

CONSISTS OF:
Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

NEEDS:
Assembly onto Car

SPECIFICATIONS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Thickness: 4mm (0.15")

REMARKS:
These are for the Within the Wheel Hubs, the Truck Requires
Four Total of these Bearings.

This is a wonderful addition to the item currently being gone over.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Construction
Black in Color
Enables Oversized Bearing use

CONSISTS OF:
One Left Axle Provider
One Right Axle Provider
Four Dust Boot Retainers
Two Bearing Spacers

NEEDS:
Installation