Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Equipment

NEEDS:
Assembly onto car

Lots of others have actually bought this product along with the product that you are currently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful product that many others have actually bought at the very same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Setup on to slipper shaft
Remaining clutch pieces

You will like this product if you have the product earlier pointed out.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

INCLUDES:
Two Ball Bearings

NEEDS:
Assembly to car

SPECS:
Inner Size: 10mm
Outer Size: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one required).

This product praises the above reviewed product.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the gear which is connected directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is only one of 2 which are used on the E-Maxx dual motor
    set-up.

This product praises the above reviewed product.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

INCLUDES:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

NEEDS:
Disassembly of slipper clutch

This is a superb addition to the product currently being reviewed.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Setup on the car

SPECS:
Length: 58mm (2.3")

Below is one more product that praises the product being reviewed.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Completely put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Connects to the differential with one screw pin
Functions on the front or back, right or left of car

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

NEEDS:
Installing on chassis