Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Totally assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Attaches to the differential with one screw pin
Works on the front or rear, right or left of car

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

REQUIRES:
Setting up on chassis

This item praises the main item right here.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto car

Lots of others have actually gotten this item together with the item that you are currently checking out.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Steel Building
Blue Rubber Sealed

INCLUDES:
Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

REQUIRES:
Assembly onto Automobile

SPECIFICATIONS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Density: 4mm (0.15")

REMARKS:
These are for the Within the Wheel Hubs, the Truck Needs
Four Overall of these Bearings.

The listed below item also sets truly well with the item being talked about.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This bundle consists of a portion of the telescoping drive shafts.

FEATURES:
Black plastic construction
Blue rubber shaft boots

INCLUDES:
Two half shaft assemblies

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Often gotten with the item that you are currently checking out.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for use on the E-Revo

FEATURES:
Stainless Steel bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside size: 6mm (0.24")
Outside size: 13mm (0.51")
Width: 5mm (0.20")

Get this item to boost the one you are reading around.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle providers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes broken axle providers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle providers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, installing 2 12x18mm ball
    bearings, stub axles, and pillow balls.

Below is a excellent item that lots of others have actually purchased the exact same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
use on the Traxxas Revo series.

FEATURES:
Nylon Building
Black in Color
Enables for Oversized Bearing utilize

INCLUDES:
One Left Axle Provider
One Right Axle Provider
Four Dust Boot Retainers
Two Bearing Spacers

REQUIRES:
Setup

Often gotten with the item that you are currently checking out.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Protects the Vehicle.

FEATURES:
Lexan construction
Pre-painted graphics
Body install holes pre-drilled
Pre-cut
Protective film covers outside of body after surface and is gotten rid of
    after conclusion of paint task

INCLUDES:
One painted graphics E-Revo Body
One decal set

REQUIRES:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECIFICATIONS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

COMMENT:
Graphics are pre-painted. Needs paint and final
decal application.