Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Outlaw Vehicles.

FEATURES:
Nylon building and construction
Black in color

CONSISTS OF:
One Receiver Box
One Rubber Seal
Foam Padding
Two 2.5x8mm Cap Head Screws
Two 3x10mm Cap Head Screws
Two 2.5x10mm Cap Head Screws
One Tube of Grease
Guideline sheet

REQUIRES:
Installation on the vehicle

SPECS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This item compliments the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this item to improve the one you read about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FUNCTIONS:
Shrouded wire connections (no diminish tube required)
Wide surface area, gold-plated terminals
Reverse polarity security makes it difficult to link in reverse
Textured surface area for simple gripping
Compatible with high-current 12-gauge wire
Secure, favorable locking spring packed terminals for constant
    contact
Numerous locking barbs keep terminals protect

CONSISTS OF:
One black female plastic connector
One black male plastic connector
Two sets of gold metal pins
Guideline sheet

REQUIRES:
Soldering wires to the metal pins

The listed below item also sets actually well with the item being talked about.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon building and construction
Black in color

CONSISTS OF:
One Installing Plate
Four 3x7.5mm Flanged Button Head Screws
Two 3x12mm Flanged Button Head Screws

REQUIRES:
Installation on the vehicle

SPECS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a wonderful addition to the item currently being talked about.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

CONSISTS OF:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This item is often bought with the above mentioned item.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

This item compliments the main item right here.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Installation on vehicle

Numerous others have bought this item in addition to the item that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.