Traxxas Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
2 front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This is a superb enhancement to the item currently being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Regularly gotten with the item that you are currently reviewing.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have more balanced out than
the stock hex wheel center set (TRAC6044).

FEATURES:
Gray plastic building and construction

INCLUDES:
2 wheel centers
2 2.5mmX12mm axle pins

SPECIFICATIONS:
Hex size: 12mm
Width: .32" (8mm)

The listed below item additionally pairs actually well with the item being reviewed.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This item is often gotten with the above mentioned item.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Regularly gotten with the item that you are currently reviewing.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This is a superb enhancement to the item currently being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on car

Right here is an additional item that compliments the item being reviewed.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building and construction

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outside size: 7mm

This item compliments the main item right here.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made of stainless-steel
This is utilized to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electric
(not Nitro) Rustler
Also called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

Right here is a wonderful item that several others have actually bought at the same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs mount to the front A-arms and is what the
guiding knuckles attach to.

FEATURES:
Nylon building and construction, black in color
Stamped right and delegated guarantee appropriate installation

INCLUDES:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly between A-arms and guiding knuckles