Traxxas Skid Plates Front & Rear (S)

This is a replacement set of skid plates for the Traxxas Stampede.

FEATURES:
Made from black molded nylon
For the Traxxas Stampede

SPECIFICATIONS:
Length of front plate: 5 5/8"
Thickness of front plate: 3/16"
Width of front plate: 2 1/8"
Length of rear plate: 4 3/8"
Thickness of rear plate: 1/8"
Width of rear plate: 2 1/8"

INCLUDES:
(1) Front skid plate
(1) Rear skid plate
MDJ 3/25/95 ¦-)

Want an additional fantastic product to enhance the above stated product?

Main Chassis (Grey)

This is the Main Chassis for the Traxxas Stampede XL-5.

FEATURES:
Nylon Building and construction
Grey in Color

INCLUDES:
One Grey Nylon Chassis

REQUIRES:
Installation into Car

This product is regularly gotten with the above stated product.

Servo Case/Gaskets For 2056 And 2075 Servos

This is the replacement Servo Case and Gasket Set for the Traxxas
2056 - TRAM2026 and 2075 (we don't stock) Servos

FEATURES:
3 piece plastic case molded in blue and black color
Changes worn or broken servo cases and gaskets

INCLUDES:
One Upper Case (blue plastic)
One Middle Case (blue plastic)
One Lower Case (black plastic)
One Upper Case Gasket
One Lower Case Gasket
One Output Shaft O-Ring
Four Case Screw O-Rings

REQUIRES:
Assembly

This product is regularly gotten with the above stated product.

Front Bulkhead (Black) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in many Traxxas vehicles.
The front suspension arm hinge pins pass through this piece.

FEATURES:
Black nylon building and construction

INCLUDES:
One front bulkhead

REQUIRES:
Absolutely nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

COMMENTS:
This part is used on the list below automobiles:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede.

Below is a fantastic product that many others have purchased the very same time.

Front Bulkhead (Gray) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in many Traxxas vehicles.
The front suspension arm hinge pins pass through this piece.

FEATURES:
Gray nylon building and construction

INCLUDES:
One front bulkhead

REQUIRES:
Absolutely nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

COMMENTS:
This part is used on the list below automobiles:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede,
    Rustler XL and Stampede XL.

You will like this item if you have the item previously mentioned.

Main Chassis (S)

This is the replacement chassis for the Traxxas Stampede truck. It is made
of black, reinforced nylon and is a channel-style chassis.

PACKAGE
INCLUDES: One chassis

COMMENTS:
The skid plates are not consisted of, use TRAC9023.

This product is regularly gotten with the above stated product.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building and construction

INCLUDES:
Two Front bearing (center) providers
Two RPM decals

REQUIRES:
(4) 5x11mm bearings, if required usage (2) DTXC1547.

Often gotten with the product that you are presently reading about.

Shock Tower Rear ( R & S)

This is the stock replacement BACK shock tower for the Traxxas Stampede.

FEATURES:
Made from black molded nylon
For the Traxxas Stampede

SPECIFICATIONS:
Width at top: 4 5/16"
Width at bottom: 2 1/4"
Thickness: 1/4"
Height: 2 13/16"

INCLUDES:
(1) Rear shock tower for the Traxxas Stampede