Traxxas Servo Case/Gaskets For 2056 And 2075 Servos

This is the replacement Servo Case and Gasket Set for the Traxxas
2056 - TRAM2026 and 2075 (we don't stock) Servos

FEATURES:
3 piece plastic case molded in blue and black color
Replaces used or broken servo cases and gaskets

CONSISTS OF:
One Upper Case (blue plastic)
One Middle Case (blue plastic)
One Lower Case (black plastic)
One Upper Case Gasket
One Lower Case Gasket
One Output Shaft O-Ring
4 Case Screw O-Rings

REQUIRES:
Assembly

Want one more wonderful product to match the above mentioned product?

Main Chassis (S)

This is the replacement chassis for the Traxxas Stampede truck. It is made
of black, reinforced nylon and is a channel-style chassis.

PACKAGE
CONSISTS OF: One chassis

COMMENTS:
The skid plates are not consisted of, use TRAC9023.

Right here is a wonderful product that numerous others have actually purchased the very same time.

Skid Plates Front & Rear (S)

This is a replacement set of skid plates for the Traxxas Stampede.

FEATURES:
Made of black molded nylon
For the Traxxas Stampede

SPECIFICATIONS:
Length of front plate: 5 5/8"
Thickness of front plate: 3/16"
Width of front plate: 2 1/8"
Length of rear plate: 4 3/8"
Thickness of rear plate: 1/8"
Width of rear plate: 2 1/8"

CONSISTS OF:
(1) Front skid plate
(1) Rear skid plate
MDJ 3/25/95 ¦-)

Want one more wonderful product to match the above mentioned product?

Main Chassis (Grey)

This is the Main Chassis for the Traxxas Stampede XL-5.

FEATURES:
Nylon Construction
Grey in Color

CONSISTS OF:
One Grey Nylon Chassis

REQUIRES:
Setup into Automobile

This product compliments the main item here.

Front Bulkhead (Gray) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in numerous Traxxas vehicles.
The front suspension arm hinge pins go through this piece.

FEATURES:
Gray nylon building and construction

CONSISTS OF:
One front bulkhead

REQUIRES:
Nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

COMMENTS:
This part is used on the following cars:
    Rustler, Bandit, Stampede, Nitro Rustler, SRT, Nitro Stampede,
    Rustler XL and Stampede XL.

The listed below product additionally pairs truly well with the product being gone over.

Large Servo Saver

This is a large servo saver that can be used in Traxxas vehicles or any vehicle that
requires a large design servo saver.
FEATURES:
Difficult white plastic construction.
INCLUDES:
1 large servo saver and 3 adaptors that enable you to install the saver
on many popular servos including: Futaba, Hobbico, Tower, Airtronics,
and Traxxas. Also consisted of is an installing screw.
SPECIFICATIONS:
Length: 1-3/8"
Size: 1"
The servo saver has 6 holes for mounting the guiding linkages.

Get this product to enhance the one you read about.

Shock Tower Front Bandit / Slash / Stampede / Rustler

This is a stock replacement FRONT shock tower for the Traxxas Stampede.

FEATURES:
Made from black molded nylon
For the Traxxas Stampede

SPECIFICATIONS:
Height: 2 3/4"
Thickness: 1/4"
Width at base: 2 3/4"
Width at top: 2"

CONSISTS OF:
(1) Front shock tower for the Traxxas Stampede

Right here is one more product that compliments the product being gone over.

Servo Gear Set #2070/2075

This is the replacement Gear Set for the 2070 & 2075 Servo.

FEATURES:
Complete gear set for the Traxxas 2070 (TRAM2070) or 2075 servo

CONSISTS OF:
4 servo gears and bearings and instruction sheet

REQUIRES:
Setup on the 2070 or 2075 Traxxas servo