Traxxas 4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building and construction

CONSISTS OF:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outdoors diameter: 7mm

Below is an additional thing that praises the thing being gone over.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This thing is frequently gotten with the above discussed thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful thing that lots of others have purchased the very same time.

Maxx Series Body Clips 12Pc

These are the Body Clips for the Traxxas E-Maxx and T-Maxx Trucks.

FEATURES:
Steel building and construction
Natural sleek color

CONSISTS OF:
Twelve Body Clips

SPECIFICATIONS:
Length: 26mm

The listed below thing also pairs actually well with the thing being gone over.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

CONSISTS OF:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

Below is a wonderful thing that lots of others have purchased the very same time.

Caster Blocks 30 Degree (L&R) Slash / Stampede / Rustler

These are Castor Blocks for the Traxxas
Rustler and Stampede.

FEATURES:
Black Plastic Building and construction

CONSISTS OF:
Two Blocks

REQUIRES:
Traxxas Rustler or Stampede

Numerous others have gotten this thing together with the thing that you are presently reading about.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
Two Front bearing (center) providers
Two RPM decals

REQUIRES:
(4) 5x11mm bearings, if required usage (2) DTXC1547.

Below is a wonderful thing that lots of others have purchased the very same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
guiding knuckles connect to.

FEATURES:
Nylon building and construction, black in color
Stamped right and delegated insure right installation

CONSISTS OF:
Two RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and guiding knuckles

You will certainly enjoy this item if you have the item just above discussed.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel building and construction

CONSISTS OF:
Two 48mm pins
Two 34mm pins
Two 30mm pins
Two 28mm pins
Two 25mm pins

REQUIRES:
Setup on the Rustler, Stampede or Bandit

REMARKS:
For a total suspension pin set order TRAC4940

You will certainly enjoy this item if you have the item just above discussed.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made from stainless steel
This is used to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electrical
(not Nitro) Rustler
Likewise called the vertical kingpin

CONSISTS OF:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97