Traxxas Rod Ends Revo Large W/ Hollow Balls

This is the Large Rod End Set for the Traxxas Revo.

FEATURES:
Plastic building
Black in color
Metal Pivot Balls

CONSISTS OF:
12 Rod Ends
12 Pivot Balls

REQUIRES:
Assembly to automobile

SPECIFICATIONS:
Length: 22mm (.88")
Width at ball joint: 10mm (.39")

Frequently acquired with the product that you are presently reading about.

Toe Link 5.0Mm Steel Frnt Or Rr (2) Revo

This is a set of replacement Toe Links for the Traxxas Revo Truck.
    These adjust the position of the toe on the vehicle.

FEATURES:
Steel turnbuckle design
5.0mm diameter

CONSISTS OF:
Two front or rear toe links

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 5.1" (129mm)

Want an additional great product to match the above pointed out product?

Turnbuckles Toe Links Rr 5Mm (

These are the Rear Turnbuckles/Toe Links for the Traxxas 3.3 T-Maxx, TRAC78**.

FUNCTIONS:
Constructed of steel, sleek natural surface

CONSISTS OF:
Two Rear Turnbuckles/Toe Links for the Traxxas 3.3 T-Maxx.

REQUIRES:
Installing in between wheel centers and rear bulkheads

SPECIFICATIONS:
Length: 4.9" (125mm)
Diameter: 0.20" (5mm)

COMMENTS:
Fits just the 3.3 variation of the T-Maxx.

Want an additional great product to match the above pointed out product?

Front Bumper Slayer

This is the Front Bumper and Mount for the
    Traxxas Slayer Pro 4WD Short Course Nitro RTR

FUNCTIONS:
Nylon building
Black in color

CONSISTS OF:
One Front Bumper
One Bumper Mount
Two 3x25mm Button Cap Screws
Two 4x10mm Button Cap Screws

REQUIRES:
Setup on the automobile

Here is a great product that lots of others have actually purchased the very same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a great product that lots of others have actually purchased the very same time.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECIFICATIONS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one needed).

This product is frequently acquired with the above pointed out product.

Rod Ends (12) / Hollow Balls (12) Jato

    These are the Rod Ends and Balls for the Traxxas Jato.

FEATURES:
Black nylon construction.
Steel hollow balls.

INCLUDES:
Twelve rod end/balls

REQUIRES:
Installing on Jato

SPECIFICATIONS:
Length: 1-1/8" (28mm)
Width: 3/8" (9mm)

The listed below product additionally pairs truly well with the product being gone over.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

CONSISTS OF:
Two front 39mm (69mm center to center) turnbuckles and guideline
    sheet

REQUIRES:
Setup on the automobile

This product is frequently acquired with the above pointed out product.



This is a optional Racers Edge Aluminum single arm servo horn, intended for usage with Futaba servos. This heavy duty aluminum servo horn is similar in design to the Racers Edge Pro Adjustable servo horns, however includes a third linkage mounting point and does not utilize lock down screws.