RPM Rear A-Arms, For Traxxas Slash, Black

    These are the RPM Strong Rear A-Arms for the
2WD Traxxas Slash Brief Course Racing Truck.

FEATURES:
Nylon construction
Black in color
Very long lasting

SUCHES AS:
2 Strong Rear A-Arms

REQUIRES:
Setup on the automobile

SPECIFICATIONS:
Length: 95mm (3.7")
Width: 47mm (1.85")
Height: 10.5mm (0.41")

COMMENTS:
Also readily available in Blue RPMC8472

Regularly gotten with the product that you are currently reviewing.

Front A-Arm, For Traxxas Slash, Rustler, Stampede, Nitro Slash,

This is a set of optional Front A-Arms for the Traxxas
Electric Stampede and Rustler.

FEATURES:
Composite nylon construction, black in color
Direct fit hop-up requires no design adjustment for setup

SUCHES AS:
2 Front A-Arms

REQUIRES:
Setup following the design manual

SPECIFICATIONS:
Length: 3.31" (84mm)
Width: .88" (22.5) at narrowist 1.52" (38.5mm) at largest

COMMENTS:
For the blue version of this part order RPMC8246

Regularly gotten with the product that you are currently reviewing.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon construction

SUCHES AS:
2 Front bearing (center) providers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if required use (2) DTXC1547.

Regularly gotten with the product that you are currently reviewing.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon construction

SUCHES AS:
2 rear bearing (center) providers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if required use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

This product compliments the main item right here.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon construction, black in color
Stamped right and delegated insure proper setup

SUCHES AS:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and steering knuckles

This product is frequently gotten with the above stated product.

Rear Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the RPM Rear Shock Tower for the
Traxxas E-Stampede, E-Rustler and E-Bandit.

FEATURES:
Strong nylon reinforced plastic construction
Uses all stock hardware (for installing shocks and so on)

SUCHES AS:
One back shock tower

SPECIFICATIONS:
Width: 4.33" (110mm)
Height: 2.75" (70mm)
Thickness: 7mm

The below product also pairs truly well with the product being gone over.

Front Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the optional RPM Front Shock Tower for the
Traxxas E-Stampede, E- Rustler, Outlaw & Nitro Stampede.

FEATURES:
Plastic construction
Black in color

SUCHES AS:
One Front Shock Tower for the Traxxas E-Stampede, E-Rustler, Outlaw
    and Nitro Stampede

REQUIRES:
Setup on the automobile

SPECIFICATIONS:
Width: 3.26" (83mm)
Height: 2.91" (74mm)
Thickness: .27" (7mm)

This product compliments the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)