Traxxas Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum building and construction
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Installation on to slipper shaft
Staying clutch pieces

Below is another item that compliments the item being talked about.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto car

You will certainly enjoy this thing if you have the thing earlier pointed out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item compliments the above talked about item.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Installation in car

Many others have actually gotten this item along with the item that you are presently checking out.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
Two Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

Below is another item that compliments the item being talked about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

CONSISTS OF:
2 Ball Bearings

REQUIRES:
Assembly to car

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one needed).

This is a amazing addition to the item presently being talked about.

Rebuild Kit Hd Slipper Clutch

This is the Strong Slipper Clutch Rebuild Kit from Traxxas.

FEATURES:
Components for both nitro and electrical Revo and Maxx trucks

CONSISTS OF:
Two Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Recommendations

REQUIRES:
Disassembly of slipper clutch

This item compliments the main item here.

Diff Carrier / X-Ring Gaskets (2) / Ring Gear Gask Et/ 6 X 1

This is the Diff Provider/Gasket Set for the Traxxas Revo.

FEATURES:
Plastic Diff Provider
Blue Rubber Shaft Gaskets
Black Rubber Diff Carrier Gaskets
Gray Washer

CONSISTS OF:
One Diff Provider
2 Blue Rubber Shaft Gaskets
One Black Rubber Diff Provider Gaskets
One Gray Washer

REQUIRES:
Assembly to car

You will certainly enjoy this thing if you have the thing earlier pointed out.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction
Black in color

CONSISTS OF:
One Input Shaft
One Bearing Adapter
One Pin

REQUIRES:
Installation on the car

SPECS:
Length: 58mm (2.3")

Below is another item that compliments the item being talked about.



This is the Rebuild Kit for the Traxxas Velineon
3500 Brushless motor - TRAC3351.

FEATURES:
Enhances efficiency of an old motor
Step-by-step direction sheet guides you through the process

CONSISTS OF:
2 5 x 11 x 5mm Bearings
One 5 x 7 x 13mm Brass Bushing
One 5 x 7 x 5.6mm Brass Bushing
4 2.5 x 5mm Button Head Screws (1.5mm hex size)

REQUIRES:
Elimination of old parts and setup of brand-new parts following the
consisted of direction sheet

REMARKS:
For the replacement motor rotor order TRAC3353
For the replacement motor cover endbell order TRAC3354