Traxxas Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Installation on the vehicle

SPECS:
Length: 58mm (2.3")

Here is a great product that many others have bought at the very same time.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Regularly gotten with the product that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a great product that many others have bought at the very same time.

Cover, Gear (Clear)

This is the optional Clear Gear Cover for use on the Traxxas Slash 4x4.
**Will not fit the Ultimate Slash LCG, for that Gear Cover, order TRAC7477.**

FEATURES:
Plastic construction
Clear in color

INCLUDES:
One Clear Gear Cover

NEEDS:
Installation on the vehicle

Here is an additional product that praises the product being gone over.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Installation on to slipper shaft
Remaining clutch pieces

The below product also pairs really well with the product being gone over.

Drive Hub, Center, Rear (1)/ F

This is the Front and Back Center Drive Hub Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel construction

INCLUDES:
One Front Center Drive Hub
One Back Center Drive Hub
One Screw Pin

NEEDS:
Installation in drive assembly

Here is a great product that many others have bought at the very same time.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

INCLUDES:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one required).

This product is frequently gotten with the above pointed out product.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless-steel Building and construction
Blue Rubber Sealed

INCLUDES:
2 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

NEEDS:
Assembly onto Automobile

SPECS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Density: 4mm (0.15")

COMMENTS:
These are for the Within the Wheel Hubs, the Truck Requires
Four Overall of these Bearings.