Traxxas Ring Gear, Differential/ Pinio

This is the Differential Ring and Pinion Gear for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Differential Ring Gear
One Differential Pinion Gear

REQUIRES:
Installation in differential assembly

SPECS:
Pinion Gear:
Tooth: 13T
Inner Diameter: 5mm (0.20")
Ring Gear:
Tooth: 37T
Inner Diameter: 6mm (0.24")

This item praises the above reviewed item.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This item praises the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will like this item if you have the item previously mentioned.

6 X 12 X 4Mm Ball Bearing (2) Blue Rubber Sheild R Evo

This is a 6X12mm Ball Bearing Set from Traxxas.

FEATURES:
Steel building
Blue rubber dirt shields

CONSISTS OF:
(2) ball bearings, Part #5117

SPECS:
Inside size: 6mm
Outdoors size: 12mm
Width: 4mm

COMMENTS:
This bearing set is used in the transmission and differentials of
    the Revo.

Below is one more item that praises the item being reviewed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one needed).

This is a superb addition to the item currently being reviewed.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Center for use on the Traxxas Slash 4x4.

FUNCTIONS:
Solidified steel building

CONSISTS OF:
One Drive Center
One Screw Pin

REQUIRES:
Installation on the vehicle

SPECS:
Length: 19mm (0.75")
Diameter: 12mm (0.47")

Below is a great item that numerous others have actually purchased the same time.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends

CONSISTS OF:
Two rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Installation on the vehicle

Get this item to enhance the one you are reading about.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends

CONSISTS OF:
Two front 39mm (69mm center to center) turnbuckles and instruction
    sheet

REQUIRES:
Installation on the vehicle

This item is regularly acquired with the above mentioned item.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Installation in vehicle