Traxxas Bulkhead Tie Bars, Front & Rea

This is the replacement Bulkhead Tie Bars for the Traxxas Slash 4X4.

FEATURES:
Aluminum building
Anodized blue in color

CONSISTS OF:
2 bulkhead tie bars (front and back)

REQUIRES:
Installation on the Slash 4X4

Regularly purchased with the thing that you are currently reviewing.

Suspension Pin Set, Complete Frt & Rr Includes Frt & Rr Swa

This is the Suspension Pin Set for the Traxxas Slash 4X4.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel building
Silver in color

CONSISTS OF:
4 51.5mm pins
4 30mm pins

REQUIRES:
Installation on the Slash 4x4

This is a superb addition to the thing currently being discussed.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Installation on to slipper shaft
Remaining clutch pieces

Regularly purchased with the thing that you are currently reviewing.

Diff Ring Gear / Pinion Gear Revo

This is the Differential Ring Gear and Pinion
for usage with the Traxxas Revo 3.3.

FEATURES:
Direct replacement part

CONSISTS OF:
One differential ring gear
One pinion gear

REQUIRES:
Traxxas Revo 3.3
2.5x8mm cap head screws (TRAC3965)

Here is a terrific thing that several others have actually bought at the same time.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Hub for usage on the Traxxas Slash 4x4.

FEATURES:
Hardened steel building

CONSISTS OF:
One Drive Hub
One Screw Pin

REQUIRES:
Installation on the automobile

SPECS:
Length: 19mm (0.75")
Size: 12mm (0.47")

Many others have actually purchased this thing along with the thing that you are currently reviewing.

58Mm Turnbuckles Camber Links (Front Or Rear) (Ass Embled W/

These are the 58mm Turnbuckle Camber Links
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends
Can be Utilized on Front or Rear

CONSISTS OF:
2 58mm Threaded Rods
4 3mm Ball Ends
4 3mm Hollow Balls

REQUIRES:
Assembly onto Vehicle

This is a superb addition to the thing currently being discussed.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Installation in automobile

You will like this item if you have the item previously stated.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Here is another thing that compliments the thing being discussed.

8 X 16 X 5Mm Ball Bearing (2) Blue Rubber Sheild R Evo

    These are the replacement Differential Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Building and construction
Blue Rubber Sealed

CONSISTS OF:
2 8mm x 16mm Rubber Sealed Bearings

REQUIRES:
Assembly onto Vehicle

SPECS:
Inner Size: 8mm (0.31")
Outer Size: 16mm (0.62")
Density: 5mm (0.19")

This thing compliments the above discussed thing.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

CONSISTS OF:
2 Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Size: 10mm
External Size: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one needed).