Traxxas Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
use on the Traxxas Revo series.

FEATURES:
Nylon Construction
Black in Color
Enables Oversized Bearing utilize

CONSISTS OF:
One Left Axle Carrier
One Right Axle Carrier
Four Dust Boot Retainers
2 Bearing Spacers

NEEDS:
Installation

Below is a great product that lots of others have bought at the exact same time.

Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

CONSISTS OF:
Four Blue Rubber Pivot Ball Boots
Four Black Dust Boot Retainer
Four Blue Notched Dust Boot Retainer
Four Blue Rubber Boot Plugs
Four nylon Pivot Ball Retainers
Direction sheet

NEEDS:
2 packages needed to finish truck

Get this product to improve the one you are reading around.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless-steel Construction
Blue Rubber Sealed

CONSISTS OF:
2 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

NEEDS:
Assembly onto Automobile

SPECIFICATIONS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Thickness: 4mm (0.15")

REMARKS:
These are for the Inside of the Wheel Hubs, the Truck Needs
Four Total of these Bearings.

Get this product to improve the one you are reading around.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for use on the E-Revo

FEATURES:
Stainless-steel bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside size: 6mm (0.24")
Outside size: 13mm (0.51")
Width: 5mm (0.20")

Want an additional great product to compliment the above mentioned product?

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Fully put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping sections from dirt
Connects to the differential with one screw pin
Works on the front or back, right or left of automobile

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Direction sheet

NEEDS:
Setting up on chassis

Several others have acquired this product along with the product that you are currently checking out.

Yokes Diff/Tranny

These are the Diff and Trans Drive Yokes for the Traxxas T-Maxx 3.3. TRAC78**

FEATURES:
Black plastic building

CONSISTS OF:
2 drive yokes
2 4x15mm Yoke pins

NEEDS:
T-Maxx 3.3

SPECIFICATIONS:
Length: 15/16" (23mm)
Size: 3/4" (17mm)

The listed below product additionally pairs actually well with the product being talked about.

Pivot Balls W/Cap

These are the Pivot Balls and Pivot Ball Cap Bushings for the
Traxxas T-Maxx and E-Maxx 4WD Radio Control Beast Trucks.
Two of these pivot balls fit into the axle providers at each wheel
    The pivot ball cap bushings fit in between the pivot balls
and the aluminum caps.

FEATURES:
Changes stock pivot balls and pivot ball cap bushings.
Pivot balls are made of steel, pivot ball cap bushings are made of
    plastic.

INCLUDES:
Four pivot balls.
Four pivot ball cap bushings

NEEDS:
Threading the pivot balls through the axle providers and into the
    suspension arms. Placing pivot ball cap bushings in between the pivot
    balls and aluminum caps.