RPM Caster Blocks & Spindle Blocks For The Slash 4X4, Stampede 4X4,

These are the optional RPM Caster and Steering Blocks for all versions of the
Traxxas Slash 4x4, Stampede 4x4 and the 1/10 scale Rally 4WD.

FUNCTIONS:
Plastic construction

INCLUDES:
Two Caster Blocks and 2 Steering Blocks

Many others have actually purchased this thing in addition to the thing that you are currently checking out.

Rear Bearing Carrier For Traxxas Slash 4X4 Or Rustler 4X4, Black

These are optional Rear Bearing Carriers for the Traxxas Slash 4x4, Nitro
Rustler, Nitro Stampede, Nitro Sport, Rad2, Hawk 2 and Eagle/Eagle LSII.

FEATURES:
Nylon construction
Black in color

INCLUDES:
Two Rear Bearing Carriers
Decal

REQUIRES:
Two 5x11x4mm ball bearings, DTXC1547

Many others have actually purchased this thing in addition to the thing that you are currently checking out.

Front Or Rear A-Arms For Traxxas Slash 4X4 Or Rustler 4X4, Red

These are the optional RPM Heavy Duty Front or Rear A-Arms in Red
for the Traxxas Slash 4x4, and Stampede 4x4.

FUNCTIONS:
Each A-arm is 0.22oz (6.5g) lighter than stock A-arm
Eliminates slop in suspension and tightens tolerances around hinge
    pins
Minimized fore and aft motion at inner hinge pin and axle carriers
    by higher than 90%
Nylon mix construction, red in color

INCLUDES:
Left and Right Front or Rear A-Arms (2 bundles required to
    complete one truck

This is a superb addition to the thing currently being gone over.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum construction

INCLUDES:
One slipper pressure plate
One slipper hub

REQUIRES:
Installation onto automobile.

Below is an additional thing that praises the thing being gone over.

Rebuild Kit Hd Slipper Clutch

This is the Heavy Duty Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Parts for both nitro and electrical Revo and Maxx trucks

INCLUDES:
3 Pads, steel Slipper Disc, 2 Locknuts, 2x9.8mm Pin, 2
    Locknuts, Spring, 2 Spring Washers and Instructions

REQUIRES:
Disassembly of slipper clutch

This is a superb addition to the thing currently being gone over.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

Below is a great thing that many others have actually bought at the same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Installation on to slipper shaft
Remaining clutch pieces

This thing praises the above gone over thing.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Heavy Duty Front/Rear A-Arms
for the Traxxas Slash 4x4.

FUNCTIONS:
Black in color
Plastic constrution

INCLUDES:
Two Front/Rear A-Arms

REQUIRES:
Installation at front or rear suspension

SPECS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at widest point
Density: 0.31" (8mm)

COMMENTS:
Likewise available in Blue (RPMC0705)