Traxxas Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

REMARKS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

This thing praises the above reviewed thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Numerous others have purchased this thing in addition to the thing that you are currently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Here is an additional thing that praises the thing being reviewed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

REQUIRES:
Setup on the automobile

REMARKS:
For primary differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037

This thing praises the main item here.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

The listed below thing also pairs really well with the thing being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

This is a amazing addition to the thing currently being reviewed.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits numerous Traxxas
automobiles. .
Includes: 1 equipment just

You will certainly like this product if you have the product just above mentioned.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Setup on automobile

Want an additional wonderful thing to match the above discussed thing?

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a amazing addition to the thing currently being reviewed.

Dust Cover/ Rubber Plug

This is a Dust Cover and Rubber Plug
for the Traxxas Rustler/Stampede

FEATURES:
Made from black molded nylon
For the Traxxas Rustler/Stampede

INCLUDES:
Dust cover for the Traxxa Rustler
3 x 6 mm round head coarse thread screws (to install dust cover)
Rubber Plug

Specs: 3" (77mm)
Suitable with Traxxas Telemetry