Dromida Shock Tower Front MT 4.18

This is the Front Shock Tower for the Dromida MT Monster Truck, DIDC0042.

FEATURES:
Molded plastic construction, black in color

CONSISTS OF:
Front Shock Tower
Two Ball Studs
4 2x8mm Round Head Screws
One Body Clip

This product is regularly gotten with the above discussed product.

Shock Tower Rear MT 4.18

This is the Rear Shock Tower for the Dromida SC Short Course Truck.

FEATURES:
Plastic construction

CONSISTS OF:
Rear Shock Tower
Two Ball Studs
4 2x8mm Round Head Screws
Two Small Body Clips

Frequently gotten with the product that you are presently reviewing.

Dogbone Set BX MT SC 4.18 (4)

This is the Dogbone Set for the Dromida BX, MT, and SC Vehicles.

FEATURES:
Plastic construction with steel pins
Fits front and rear drive systems

CONSISTS OF:
4 Dogbones

This is a great addition to the product presently being talked about.

Body Clip BX MT SC 4.18 (10)

These are the Body Clips for the Dromida SC, MT and BX Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
Ten Body Clips

Frequently gotten with the product that you are presently reviewing.

Suspension Arm Lower BX MT SC 4.18 (2)

These are the Lower Suspension Arms for the Dromida SC, MT and BX Vehicles.

FEATURES:
Plastic construction
Fits front or rear suspension

CONSISTS OF:
Two Lower Suspension Arms

Below is a fantastic product that lots of others have actually purchased the exact same time.



This is the Bumper Set for the Dromida MT Monster Truck.

FEATURES:
Plastic construction, black in color
Versatile to stand up to minor crashes

CONSISTS OF:
Front and Rear Bumpers
4 2.8mm Round Head Screws

Numerous others have actually gotten this product together with the product that you are presently reviewing.

Shock Long BX MT SC 4.18 (2)

This is a set of Long Shocks for the Dromida BX, MT, and SC Vehicles.

FEATURES:
Plastic bodies
Assembled and prepared to install

CONSISTS OF:
Two Long Shocks
Two each 1mm, 2mm and 4mm Preload Spacers
Two Spring Clamps

This is a great addition to the product presently being talked about.

Drive Shaft Spacer Set BX MT SC 4.18

This is the Drive Shaft Spacer Set
for the Dromida SC4.18, MT4.18 and BX4.18 Vehicles.

FEATURES:
Installs on either side of put together differential

CONSISTS OF:
4 O-Rings
    4 Springs, essential #35

You will certainly enjoy this item if you have the item earlier pointed out.



This is the DuraTrax 1600mAh NiMH 7.2V 6 Cell Stick Battery Pack.

FEATURES:
For use with the Duratrax Vendetta, Mini Quake and Cliff Climber but
    can likewise be utilized in other 1/18 scale applications

CONSISTS OF:
DuraTrax 1600mAh NiMH 7.2V 6 Cell Stick Battery Load with mini
    female port

REQUIRES:
Charger efficient in charging NiMH batteries, such as the DuraTrax
    IntelliPeak series or the Great Planes TRITON series

SPECIFICATIONS:
Capacity: 1600mAh
Cell Size: 2/3A
# of Cells in Series: 6
Ranked Voltage: 7.2V
Minutes. Discharge Voltage: 5.4V
Maximum Recommended Charge Current: 1.2A
Discharge Lead: 20AWG 2.4" (60mm) long wire
Load Measurements: 86 x 34 x 17mm (3.38 x 1.33 x 0.66 inches)
Weight: 147g (5.2oz)
Number of welds per connection: 6
Connector: 1/18 scale mini female

Below is one more product that praises the product being talked about.



This is the DuraTrax LiPo 7.4V 1600mAh 20C Tough Case Mini Battery Load
with Mini Plug.

FEATURES:
For use in the DuraTrax Vendetta, Mini Quake, Cliff Climber and other
    1/16 to 1/18 scale cars that use batteries with mini plugs

CONSISTS OF:
DuraTrax LiPo 7.4V 1600mAh 20C Tough Case Battery Load with Mini Plug

REQUIRES:
Balancer such as the Group Checkpoint Balancer, and TWO
    Adapter XH Plug,

SPECIFICATIONS:
Capacity: 1600mAh
Number of Cells in Series: 2
Ranked Voltage: 7.4V
Continuous Discharge Rate: 20C
Maximum Recommended Charge Current: 1C (1.6 amps)
Charge Lead: 24AWG, 1.2" (30mm) long wire w/XH Balance Plug
Discharge Lead: 20AWG, 3.5" (90mm) long wire w/Mini Plug
Load Measurements: 3.3 x 1.2 x 0.7" (85 x 31 x 17mm)
Weight: 3oz (85g) all plugs and wires are included in weights

REMARKS:
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER allow to Discharge below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any method or leak cells
NEVER put on combustible materials or leave ignored during
    charging
ALWAYS Charge in a fire-resistant area
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of children
All weights include wire leads and plugs
All weights +/- 1g
All measurements +/- 1mm