Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outside diameter in between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature as much as 30°
One year minimal warranty through manufacturer start at date of
    purchase

INCLUDES:
Fan with wire and connector, shroud and 2 zip ties

NEEDS:
Attaching to motor can and connecteding into receiver

SPECS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want one more great item to match the above pointed out item?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases utilized on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws required

INCLUDES:
Fan with Wire Lead and Port
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove before exposing ESC to moisture

The below item also pairs really well with the item being talked about.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Suggested for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for use in much heavier
    automobiles such as E-Revos or E-Maxx class automobiles)
USB shows ability via Castle Link USB adapter (not included,
    order CSEM6300)
Water resistant for use in nearly every environment (not planned for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces many stock brushed motors
Four magnet, 4 pole rotor for higher torque
1.4" diameter slotted stator
Removable end bell

INCLUDES:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Change, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

NEEDS:
Battery connector of modeler's option

SPECS:
ESC;
Input Voltage: TWO LiPo minimum, 3S LiPo maximum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery connector
    Motor;
kV Score: 4600
Can Length: 1.9" (49mm)
Can Diameter: 1.4" (36mm)
Shaft Diameter: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)

Many others have actually bought this item together with the item that you are presently reading about.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Villain IV.
AXY
4/8/92

Right here is one more item that praises the item being talked about.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is connected directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of 2 which are utilized on the E-Maxx dual motor
    set-up.