Traxxas 15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are used on the E-Maxx dual motor
    set-up.

Several others have actually acquired this thing together with the thing that you are presently checking out.

17T Pinion Gear 32P

This is a 17 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 17 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are used on the E-Maxx dual motor
    set-up.

Several others have actually acquired this thing together with the thing that you are presently checking out.

14T Pinion Gear 32P

This is a 14 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 14 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are used on the E-Maxx dual motor
    set-up.

Get this thing to enhance the one you read around.

16T Pinion Gear 32P

This is a 16 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 16 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are used on the E-Maxx dual motor
    set-up.

This thing compliments the above gone over thing.

18T Pinion Gear 32P

This is a 18 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 18 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are used on the E-Maxx dual motor
    set-up.

You will love this item if you have the item just above discussed.

Slipper Clutch Complete Stampede 4X4

This is the Complete Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Complete slipper clutch assembly
Pre-assembled

INCLUDES:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

NEEDS:
Setup in automobile