APC 7x5 Thin Electric Prop

This is a 7x5E Thin Composite propeller from Advanced Precision Composites.
For use on Electric powered aircraft only (not for radiance engines).

FUNCTIONS:
Gray composite propeller blades that put together onto a propeller hub.
Comes with 2 adjuster rings that adapt to various motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
Two composite adapter rings
One direction sheet

REQUIRES:
ALL props need balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 7"
Pitch: 5
Center inner size: 0.25"

You will like this thing if you have the thing previously stated.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Precision Composites.
For use on electric powered aircraft only (not for radiance engines).

FUNCTIONS:
Gray composite building and construction
Includes 2 adjuster rings that adapt to various motor shafts

CONSISTS OF:
One 7x6EP Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 7"
Pitch: 6
Center inner size: 0.25" (6.3mm)

Right here is another item that praises the item being discussed.



This is a 6x5.5E Thin Composite Propeller from Advanced Precision Composites.
For use on Electric powered aircraft only (not for radiance engines).

FUNCTIONS:
Gray composite building and construction

CONSISTS OF:
One 6x5.5E Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 6"
Pitch: 5.5
Center inner size: 0.25"

The below item also sets really well with the item being discussed.



These are the ElectriFly Prop Saver O-rings from Excellent Planes.

FEATURES:
Twists around the prop to hold it on and protect it during crashes

CONSISTS OF:
5 prop saver O-rings

REQUIRES:
Setup

Several others have gotten this item along with the item that you are presently reading about.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specs:
Dimension : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing material:
1 x 9g TITAN Servo Sets (with devices)

Want another great item to compliment the above stated item?

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction decreases turning mass for
    greater output and longer life.
Reinforcing carbon fibers assist preserve real, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring direction sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not created for Glow engines