APC 6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Accuracy Composites.
For use on Electric powered aircraft just (not for glow engines).

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with two adapter rings that adapt to various motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
2 composite adapter rings
One guideline sheet

REQUIRES:
Assembly onto motor or equipment drive device in your Electric plane.
Balancing

SPECS:
Size: 6"
Pitch: 4
Hub inner size: 0.25"

COMMENTS:
Usage Speed 400 Electric motors.

This item is often purchased with the above pointed out item.

6x4 Speed 400 Electric Pusher Prop

This is a 6x4 Speed 400 Electric Pusher Propeller
from Advanced Accuracy Composites.
For use on Electric powered aircraft just, not for glow powered engines.

FEATURES:
Constructed of Gray composite material
For Speed 400 motor applications
2 adapter rings that adapt to various motor shafts

INCLUDES:
6x4 Speed 400 Electric Pusher Propeller, two adapter rings and
    guideline sheet

REQUIRES:
Assembly onto motor shaft or equipment drive device in Electric plane

SPECS:
Size: 6"
Pitch: 4
Hub inner size: 0.24" (6mm) where rings are installed
Inner Size of Rings: 0.188" (4.8mm) and 0.236" (6mm)

Right here is a fantastic item that numerous others have actually purchased the very same time.



This is a 6x5.5E Thin Composite Propeller from Advanced Accuracy Composites.
For use on Electric powered aircraft just (not for glow engines).

FUNCTIONS:
Gray composite construction

INCLUDES:
One 6x5.5E Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Size: 6"
Pitch: 5.5
Hub inner size: 0.25"

Frequently purchased with the item that you are presently checking out.

Prop Adapter with Collet, 2mm




Right here is a fantastic item that numerous others have actually purchased the very same time.

Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for usage on 28mm Motors.

FEATURES:
Aluminum construction

INCLUDES:
One Prop Saver
2 Rubber O-Rings
2 Bushings

REQUIRES:
Setup on Rimfire 28mm Motor

Right here is an additional item that compliments the item being gone over.

Nylon Kwik-Link On 12" 2-56 Rod (5/Pkg)

These are Threaded Rods with Nylon Kwik Links.

FEATURES:
Steel rod construction w/ 2-56 threads
Nylon clevis construction

INCLUDES:
Five steel threaded rods 12" long, thread length 3/4", .072" size
Five 2-56 nylon clevises 7/8" long

SPECS:
See "Includes" above

COMMENTS:
For bulk qty of 12, use DUBQ1580.

The listed below item also sets really well with the item being gone over.

Control Horn Nylon 1/2A (2)

These are 1/2A T-Style Control Horns.

FEATURES:
Nylon construction

INCLUDES:
2 control horns w/4 adjusting holes and 2 mounting holes
(3/4" long [tall])
2 mounting plates w/2 mounting holes (3/8"x3/8")
Four 2-56x3/8" round head screws

REQUIRES:
A flat head (slotted) screwdriver

SPECS:
See "consists of" above

Right here is a fantastic item that numerous others have actually purchased the very same time.



These are two W.S. Deans 2-Pin Female Ultra Plug Connectors.

FEATURES:
Eliminates the possibility of reverse polarity connections
Low resistance, compact size
Provides a protected connection for battery and motor connections on
    R/C automobiles

INCLUDES:
2 WS Deans 2-Pin Female Ultra Plug Connectors with section of
    shrink tubing

REQUIRES:
Soldering ports onto wires
Soldering iron HCAR0776
Solder STAR2000

COMMENTS:
For Male end usage WSDM1302
For both Male and Female usage WSDM3001