APC 8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction lowers turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist keep true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring guideline sheet

REQUIRES:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not created for Radiance engines

This is a superb enhancement to the product currently being reviewed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Lightweight molded nylon building and construction lowers turning mass for
    higher output and longer life
Created for electric powered Park Leaflet type aircraft with rear
    facing motors that "push" the plane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with 2 finding rings and
    guideline sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center diameter: 0.50"
Hole Diameter: 1/4"

REQUIRES:
Only for usage with electric motors. Not for usage with glow or gas
    engines.
All props require balancing, this is EXTREMELY IMPORTANT, utilize TOPQ5700.
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

This product is often bought with the above discussed product.



This is the Futaba S3003 Standard Servo.
This fundamental servo is used in automobiles, boats, or where conventional servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of delivering enough amps.

INCLUDES:
One S3003 conventional servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year service warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Connector: "J" type with approx. 5" lead

This product compliments the above reviewed product.

Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and light-weight for installing in small airplanes,
    electrics or gliders, where very high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train offers dependable operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One very small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
Two M1.7x7 servo installing screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)