APC 8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon construction minimizes turning mass for
    greater output and longer life
Created for electric powered Park Flyer type airplane with rear
    facing motors that "push" the airplane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with 2 locating rings and
    guideline sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center size: 0.50"
Hole Diameter: 1/4"

NEEDS:
Just for usage with electric motors. Not for usage with radiance or gasoline
    engines.
All props need balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

Frequently bought with the thing that you are presently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction minimizes turning mass for
    greater output and longer life.
Reinforcing carbon fibers assist preserve true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring guideline sheet

NEEDS:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Radiance engines

Frequently bought with the thing that you are presently reading about.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is utilized in vehicles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, ensure they are capable
of delivering adequate amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangle-shaped rubber grommets (FUTM2348)
4 servo install screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

This thing compliments the above gone over thing.

Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and lightweight for mounting in small planes,
    electrics or gliders, where really high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train provides dependable operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One really small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)