Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a 6S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below product also sets actually well with the product being talked about.

4S JST-XH Lipo Balance Wire Extension Lead

This is a FOUR JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Numerous others have actually gotten this product along with the product that you are presently reading about.

EC5 Device Connector (2)


Functions



With the ability of more than 120A continuous current with 10-awg wireErgonomically pleasing and easy to gripProtected to prevent shorting and reverse polaritySuperior innovation fit to today's sophisticated applicationsDesigned with benefit and reliability in mind




Overview


E-flite's high-quality EC5 adapters must be a staple for every workbench. EC5 (E-flite Connector 5mm) adapters, leads with adapters, and accessories are ideal for electric power applications and work with any battery, charger, ESC, Power Meter, and so on. They are perfect for high power applications.

Numerous others have actually gotten this product along with the product that you are presently reading about.

EC5 Extension Lead with 6" Wire, 10Awg




Regularly gotten with the product that you are presently reading about.

Servo line Color Black & Green

Planning to clean up the look of your helicopter, aircraft of RC car & protect your servo lines from chaffing? Servo Line Covering is a simple way to protect your servo wires, adding a clean, aesthetic aim to your RC device, and can be set up in a matter of minutes. Select from our amazing line of diverse colors to add an entire new look to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply eliminate your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, thus offering you a flush, tight fit over the formerly frayed servo covering. Do the same with completion of your servo wire, bewaring to leave the terminal bare so it can easily plug into your receiver. Likewise, make sure to keep in mind of the servo wire polarity if you cover the full wire – this will make sure that you will understand what instructions to plug your servo terminal into your receiver.

Here is a fantastic product that several others have actually purchased the very same time.

Servo line Color Blue/Black (1m)

Planning to clean up the look of your helicopter, aircraft of RC car & protect your servo lines from chaffing? Servo Line Covering is a simple way to protect your servo wires, adding a clean, aesthetic aim to your RC device, and can be set up in a matter of minutes. Select from our amazing line of diverse colors to add an entire new look to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply eliminate your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, thus offering you a flush, tight fit over the formerly frayed servo covering. Do the same with completion of your servo wire, bewaring to leave the terminal bare so it can easily plug into your receiver. Likewise, make sure to keep in mind of the servo wire polarity if you cover the full wire – this will make sure that you will understand what instructions to plug your servo terminal into your receiver.