Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Gear for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for designs with a slipper clutch.
Black plastic building

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is also a 86T equipment (TRAC4686),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

This is a wonderful addition to the product currently being reviewed.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Gear for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for designs with a slipper clutch.
Black plastic building

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Get this product to boost the one you are reading around.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Gear with Set Screw
from Traxxas.

FEATURES:
Steel building, silver in color

SUCHES AS:
One 31 Tooth, 48 Pitch Pinion Gear
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Setup

SPECIFICATIONS:
Length: .42" (10.5mm)
Inside Diameter: 1/8"
Outdoors Diameter: .69" (17.5mm)

Lots of others have purchased this product together with the product that you are currently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Here is one more product that compliments the product being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

SUCHES AS:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

REQUIRES:
Disassembly of slipper clutch

Get this product to boost the one you are reading around.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want one more great product to enhance the above pointed out product?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These may also be referred to as coverplate screws.

This product is regularly purchased with the above pointed out product.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

SUCHES AS:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Automobile

This product compliments the above reviewed product.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Only (No Wires).

FUNCTIONS:
Shrouded wire connections (no shrink tube needed)
Wide area, gold-plated terminals
Reverse polarity protection makes it impossible to link in reverse
Textured surface area for simple gripping
Suitable with high-current 12-gauge wire
Secure, favorable locking spring loaded terminals for constant
    contact
Several locking barbs keep terminals secure

SUCHES AS:
Two black female plastic adapters
Two sets of gold metal pins
Instruction sheet

REQUIRES:
Soldering wires to the metal pins