Traxxas 3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These might also be referred to as coverplate screws.

Regularly acquired with the product that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below product also pairs really well with the product being discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Vehicle

This is a fantastic enhancement to the product presently being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Several others have actually acquired this product along with the product that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Here is a fantastic product that many others have actually purchased the same time.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum building and construction

INCLUDES:
One slipper pressure plate
One slipper center

REQUIRES:
Installation onto automobile.

You will certainly enjoy this thing if you have the thing above pointed out.

Rebuild Kit Hd Slipper Clutch

This is the Sturdy Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Parts for both nitro and electric Revo and Maxx trucks

INCLUDES:
Three Pads, steel Slipper Disc, 2 Locknuts, 2x9.8mm Pin, 2
    Locknuts, Spring, 2 Spring Washers and Instructions

REQUIRES:
Disassembly of slipper clutch

This product is frequently acquired with the above discussed product.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Designed for models with a slipper clutch
Black plastic building and construction

INCLUDES:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Regularly acquired with the product that you are presently checking out.

3X8mm Screws Flat-Head (Hex Drive) (6)

These are the Traxxas Flathead 3 x 8mm Screws.

FEATURES:
Metal building and construction
Black in color

INCLUDES:
Six 3 x 8mm Flathead Hex Screws

REQUIRES:
Installation on the automobile

This is a fantastic enhancement to the product presently being discussed.

3 X 8Mm Counter Hex Screw (6)

These are 3x8mm Countersunk Hex Head Screws by Traxxas.
Can be used anywhere this kind of screw is needed.

FEATURES:
Metal Building and construction
Black in Color
Countersunk

INCLUDES:
(6) Screws

SPECIFICATIONS:
Length: 8mm
Diameter: 3mm