Traxxas Shrt Rod Ends/Ball Cnnctr (6)

This are Rod Ends Short for the Nitro T-Maxx.
These rods ends attach to turnbuckles for front/rear.

FEATURES:
Black nylon rod ends
Steel pivot balls

INCLUDES:
Six nylon rod ends
Six pivot balls

REQUIRES:
Turnbuckles: TRAC6338

SPECS:
Length: .695" (17.6mm)
Inner Size: .217" (5.5mm)

REMARKS:
Will work just for the Nitro T-Maxx.

This is a superb enhancement to the thing currently being talked about.

3 X 15Mm Button Hex Screw (6)

This is a plan of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel building, Black in color
Used on the Traxxas Revo monster truck, can likewise be used in any
    application where a 3x15mm button head screw is needed

INCLUDES:
Six 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Size: 3mm

Lots of others have actually gotten this thing along with the thing that you are currently checking out.

Antenna Tube W/ Cap, Black

This is a conventional replacement Antenna Tube with Cap from Dubro
This product can be used anywhere an antenna tube is required to support
a receiver antenna wire.

FEATURES:
Black plastic building

INCLUDES:
One antenna tube
One antenna tube cap
One receiver antenna wire sleeve

REQUIRES:
Absolutely nothing. This is a direct fit part for any boat, vehicle, and so on that utilizes
    a conventional size antenna tube.

SPECS:
Length: 12 1/4" (311mm)
Size: 1/8" (3.2mm)

You will like this thing if you have the thing just above mentioned.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

Here is a great thing that numerous others have actually bought at the exact same time.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Construction

INCLUDES:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

REMARKS:
None

Want another great thing to match the above discussed thing?

Rod Ends/Ball Connector (6)

These are 5.8mm ball ends and balls utilize in the LS II race truck kit.

Kit suches as: 6ea 5.8mm metal balls
6ea 5.8mm white nylon ball ends

pcd 01/10/94

The below thing likewise sets really well with the thing being talked about.

Shock Rebuild Big Bore/Ultra

This is a shock reconstruct kit for 2 Traxxas black plastic shocks. Consists of:

4 E-clips
2 C-clips
2 O-rings
8 Washers
2 Diaphrams

This thing is frequently gotten with the above discussed thing.

Shock Shafts Chrome Xxl (2)

This is a set of XXL shock shafts for the Traxxas shocks.

Includes: 2 shock shafts

Features: hardened chrome/steel building

Specs: 2 1/8" long or 54mm
1/16" size or 1.5mm

Needs: Additional long shocks

Comments: These are threaded on one end, and have the slots for e-clips on the
other.

4/16/97
AST

This is a superb enhancement to the thing currently being talked about.

Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set contains the spring retainers that hold the springs in
restaurant over the shock body and the piston heads that manage the quantity
of oil circulation in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for two shocks.
Fits the shocks on many Traxxas nitro and electric powered vehicles.
Two hole piston head for higher dampening or 3 hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    2 upper and two lower spring retainers
    2 2 hole piston head covers
    Two 3 hole piston head covers

REQUIRES:
Disassembly of shock to set up parts.