Suppo Model 1400Kv Brushless Outrunner Motor, 3.17MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1250Kv
Max. performance current: 6-12 Amp
NoLoad current / 0.7 Amp
Present capacity: 16 A/60 s
Max. Effectiveness: 75%
Shaft size: 3mm
Weight with cable televisions: 47g
Measurements(mm): 27.5x30

Recommended Model Weight: 300 - 800 g
Recommended Prop w/o Gearbox: 7 cells (2xLi) 9."x5; 8 cells 9x5; 10 cells 8.5x6; 3xLi 8x4

Lots of others have actually purchased this item in addition to the item that you are currently reviewing.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction lowers rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain real, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring direction sheet

NEEDS:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not created for Radiance engines

Get this item to boost the one you read about.

8x6EP Thin Electric Pusher Propeller

This is a 8x6EP Thin Composite Propeller from Advanced Accuracy Composites.
For use on electric powered airplane just (not for glow engines).

FUNCTIONS:
Gray composite construction
Includes five adjuster rings that adapt to different motor shafts.

INCLUDES:
One 8x6EP Thin Electric Propeller

NEEDS:
ALL props require balancing, this is ESSENTIAL, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Size: 8"
Pitch: 6
Center inner size: 0.25" (6.3mm)

This item compliments the above gone over item.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Gear Type : All Nylon Gear
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specifications:
Dimension : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Variety : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing content:
1 x 9g TITAN Servo Sets (with devices)

You will certainly love this product if you have the product just above mentioned.

10x4.7 Slow Flyer Propeller

This is a 10x4.7 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction lowers rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain real, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring direction sheet

NEEDS:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7

COMMENTS:
Slo-Flyer props are Not created for Radiance engines