APC 10x4.7 Slow Flyer Propeller

This is a 10x4.7 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building and construction lowers turning mass for
    higher output and longer life.
Reinforcing carbon fibers help keep real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring direction sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7

REMARKS:
Slo-Flyer props are Not created for Glow engines

Many others have actually gotten this thing along with the thing that you are currently reading about.

10x4.7 Slow Flyer Pusher

This is the APC 10x4.7 Slo-Flyer Pusher Electric Propeller.

FEATURES:
Opponent electrical and Park-Flyer type airplane
Pusher propellers formed in the opposite direction from conventional
    propellers, they are created for airplanes with the motor dealing with
    in reverse in the rear of the airplane, PUSHING the airplane forward
Lightweight molded nylon building and construction lowers turning mass for
    higher output and longer life
Reinforcing fibers help keep real, constant pitch at any RPM

CONSISTS OF:
APC 10x4.7 Slo-Flyer Pusher Electric Propeller
0.236" (5.9mm) and 0.188" (4.8mm) finding rings
Direction sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7"

REMARKS:
Slo-Flyer props cannot be used on glow or gasoline powered engines

Right here is a wonderful thing that several others have actually purchased the very same time.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Measurement : 23mm x 12mm x 29mm
Connector Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packaging content:
1 x 9g TITAN Servo Sets (with devices)

Right here is one more thing that praises the thing being gone over.

9x4.7 Slow Flyer Propeller

This is a 9x4.7 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Composite building and construction
Reinforcing carbon fibers help keep real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring direction sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 9"
Pitch: 4.7

REMARKS:
Slo-Flyer props are Not created for Glow engines