Hot Racing 9.5G Brass Kmc Machete Wheel Weights, For Axial Scx24

9.5g Brass KMC Machete Wheel Weights, for Axial SCX24

Hot Racing front or rear wheel weights for the stock 1.0in KMC Machete wheels on the Axial SCX24.

Features:

CNC machined solid brass billet

9g each fitted to the wheels to lower the automobiles center of mass, increase its stability, enhance climbing up, minimize the chance for turning in reverse, and produce an overall more capable spider

Friction fit to within KMC Machete wheels. Some CA glue can be utilized to secure installation

Can be utilized either in front of rear, but if you're only getting one set we advise utilizing them in the front

Specifications:

Hub: 12mm hex

For : AXI31615

Diameter of external : 21.4mm

Diameter of within : 12mm

Weight: 9.5g/ea

Width: 8mm

Frequently gotten with the thing that you are presently checking out.

9G Brass Differential Cover, For Axial Scx24

9g Brass Differential Cover, for Axial SCX24

Hot Racing heavy brass cover for SCX24 Worm equipment Axles Includes 9g of weight to the axle in a low and central place to lower the vehicle's center of gravity, increase its stability, and make it an in general more capable crawler.

Features:

CNC machined solid brass billet

Includes 9g of low and central weight to lower and centralize the vehicle's center of mass, increase its stability, and make it an

Overall more capable crawler

mm increased density over stock cover for extra strength and weight

Fits either the front or rear

Specifications:

Width:14.33 mm

Height:24 mm

Weight: 9g

Want an additional excellent thing to enhance the above discussed thing?

Brass Front Steering Knuckle, For Axial Scx24

Brass Front Steering Knuckle, for Axial SCX24

Hot Racing sturdy brass SCX24 Worm equipment Axles steering knuckles (steering blocks) for the Axial SCX24 axles. Add weight to your spider where it requires it - down low.

Features:

CNC machined solid brass

Heavy to include weight to vehicle for higher stability and lower CG

Cutouts on knuckle for access to external bearing race for simple bearing elimination

Direct replacement for factory plastic steering knuckles

Want an additional excellent thing to enhance the above discussed thing?

Brass Stock Wheels Hub, 7Mm Hex, For Scx24

Brass Stock Wheels Hub, 7mm Hex, for SCX24

Features:

CNC Machined Strong Brass construction.

You Will Get:

Four Hex Wheel Centers

Four 2 x 6mm Axle Pins

Requirements:

Assembly onto SCX24.

Specs:

Hex: 7mm

Inner diameter: 4mm

Right here is a excellent thing that lots of others have purchased the same time.

Aluminum Front Bumper W/Fairlead And Light Buckets, For Axial Sc

Aluminum Front Bumper w/Fairlead and Light Buckets, for Axial SCX24

Hot Racing CNC machined aluminum front bumper with 3mm LED light containers, winch fairlead for use with Axial SCX 24.

Features:

Billet CNC machined aluminum

Anodized a stylish flat black

Integrated brush guards

Light containers for 3mm LED lights

Specifications:

Width: 58mm

Height: 8mm

Right here is a excellent thing that lots of others have purchased the same time.

SCX24 Deadbolt 1/24th Scale Elec 4WD - RTR, Red

Key Features:
• Includes radio system, ESC and transmitter batteries
• Includes motor and on-board LiPo battery
• Practical narrow-stance rock spider body in olive green or red
• Molded roll cage with practical light bar
• Practical driver figure and lots of other scale details
• Formally certified KMC XD229 Machete Crawl wheels
• Formally certified Nitto Trail Grappler M/T tires (S30 compound, large block tread)
• Full-time 4WD
• Splined and sleeved front and rear drive shafts enable maximum suspension travel while keeping the power to the wheels
• Steel front and rear axles, front stub axles and dogbones supply strength and resilience
• Rugged steel C-channel frame rails with bracing keep everything rigid and aligned
• Front and rear axles consist of a two-piece, molded plastic solid axle design
• 3-Link front and 4-link rear suspension supply optimum handling
• Coil-over shocks with simulated reservoir and long lasting plastic suspension links deliver proven Axial crawling performance
• Front and rear differentials each home a worm equipment setup to power the axles and produce greater ground clearance. Worm equipment drive also offers a low equipment ratio to minimize torque twist
• 2 LEDs in the front bumper for night driving
The SCX24™ Deadbolt™ 4WD is the very first Axial® off-roader in 1/24 scale. At less than 8” long, it’s the ideal rig to take along on your hiking, outdoor camping, and other outdoor and indoor experiences — offering factory-assembled ease, scale looks, and confident handling on any trail.

Even new modelers driving the SCX24 chassis will be fully equipped to deal with tough climbs up and rough routes. Like the larger SCX10™ chassis, this smaller sized version uses lots of steel elements — from the C-channel frame rails to the front and rear axles and dogbones. Even over off-road, mountainous, rocky and desert terrain, it has the strength to keep pressing onward and upward.

For the most reputable handling, the SCX24 chassis includes a three-link front and four-link rear suspension. The combination of coil-over shocks and long lasting plastic suspension links delivers Axial-worthy crawling performance even at this small scale. The worm equipment drive setup permits a high ground clearance plus a low equipment ratio that lowers torque twist.

Powered by an included 180-size motor and LiPo battery, the SCX24 Deadbolt shows off competence and charisma on the routes. Take a look at that Deadbolt body — with its narrow position, bulging hood, practical driver figure, and molded roll cage with practical light bar. The realism continues right down to the ground, where you’ll discover certified KMC XD229 Machete Crawl wheels wrapped in Nitto Trail Grappler tires.

Adding a lot more to its beginner appeal, the SCX24 Deadbolt comes 100% total and ready to run. Whatever required for action remains in the box: assembled and completed vehicle; Axial 2-channel 2.4GHz radio system with servo and ESC/receiver system; Dynamite® 88T brushed electric motor and 350mAh TWO 7.4V LiPo battery; USB LiPo charger; and even four AA cells for the transmitter!

What's in package?
(1) SCX24™ Deadbolt™ 1/24 Scale 4WD Truck
    (1) Axial AE-6 ESC/receiver combo (installed)
    (1) Dynamite® 88T brushed electric motor (installed)
    (1) Axial AS-1 steering servo (installed)
(1) Axial® AX-4 2.4GHz 2-channel radio
(4) AA transmitter batteries
(1) 350mAh TWO 7.4V LiPo battery
(1) USB LiPo charger
(1) Product Handbook




STEEL C-CHANNEL CHASSIS FRAME RAILS
Similar to the 1/10th scale SCX10™ platform, the SCX24™ chassis features rugged and strong steel c-channel frame rails with bracing to keep everything intact and aligned.
 

DYNAMITE® 88T BRUSHED MOTOR
The Dynamite 88T brushed electric motor offers the right amount of torque to assist ascend steep climbs up. It's mated to a steel motor install to keep flex to a minimum, which assists secure the gears.
 


WORM GEARS
The front and rear differentials each home a worm screw and worm equipment setup to get the power to the axles and produce greater ground clearance.
 

DURABLE STEEL AXLES
Steel front and rear axles, front stub axles in addition to steel dogbones supply strength and resilience to keep things running during tough climbs up and rough routes.
 


SPLINED DRIVE SHAFTS
The front and rear drive shafts are splined and sleeved to enable maximum suspension travel while keeping the power to the wheels.
 

COILOVER SHOCK ABSORBERS
Even at this small scale, the combination of coilover shocks with simulated reservoirs and long lasting plastic suspension links delivers the crawling performance you've understood and get out of Axial.
 


FRONT AND REAR SOLID AXLES
The front and rear axles consist of a two piece, molded plastic solid axle design. For optimum handling, the SCX24™ suspension includes a three-link front and four-link rear setup.
 


LED LIGHTS INCLUDED
2 brilliant LED lights are included and are installed in the front bumper. An additional LED light port on the ESC permits you to include optional LED lights.
 

4-LINK REAR SUSPENSION
The suspension geometry uses a 4-Link design for the rear which is optimized to minimize axle steer and torque twist. We've also included additional suspension links for adjusting your wheelbase length.
 


KMC XD229 MACHETE CRAWL WHEELS & NITTO TRAIL GRAPPLER M/T TIRES
Formally certified KMC XD Machete wheels are legendary in the off-road world. They are molded in black and function spectacular scale details, in spite of the small scale.
The formally certified Nitto Trail Grappler M/T Tires use a wonderful mix of off-road performance while still keeping outstanding composure for on-road use.
 

HINGED BODY SYSTEM
The hinged body system uses simple access to on-board elements. You can rapidly reach the battery and chassis by removing just two body clips and swinging the body up.
 


FULL BALL BEARINGS
Even if the SCX24™ is smaller sized in size does not indicate the features require to do the same. No bushings found here, rather the drivetrain is freely spinning on sealed cartridge bearings throughout the whole vehicle.
 

AXIAL AS-1 SERVO
Mounted just above the front axle is the Axial AS-1 servo, with a servo saver that allows for steering accuracy, while also providing protection for the servo gears in the event of a bind or impact.
 

Specifications

Type: Spider
Scale: 1/24
Length: 7.8" (199.5mm)
Width: 3.9" (99.5mm)
Height: 4.73" (120.2mm)
Ground Clearance: 1.06" (27mm)
Wheepoundase: 5.25" (133.5mm)
Weight: 0.5lb (0.22kg)
Chassis: Stamped steel rails
Suspension: Strong axle, front and rear
Drivetrain: 4WD
Tire Type: Nitto Trail Grappler M/T, large block tread
Speed Control: AE-6 ESC receiver/combo
Radio: AX-4 2.4GHz 2-channel
Servos: AS-1 steering servo
Batteries: 7.4V 350mAh 30C LiPo (included)
Battery charger: USB LiPo charger (included)
Equipment Pitch: 32-Pitch
Wheel Size: 0.48" (12.4mm) width, 1.0" (26mm) diameter
Kit/RTR: RTR
Shock Type: Plastic body coil-over .9 - 1.3" (24 - 33.4mm)
Body: Painted and cut Axial Deadbolt
Ball Bearings: Complete body
Is Assembly Required: No