Hot Racing 9G Brass Differential Cover, For Axial Scx24

9g Brass Differential Cover, for Axial SCX24

Hot Racing heavy brass cover for SCX24 Worm gear Axles Adds 9g of weight to the axle in a low and centralized place to decrease the lorry's center of gravity, increase its stability, and make it an in general more capable crawler.

Features:

CNC machined strong brass billet

Adds 9g of low and main weight to lower and centralize the lorry's center of gravity, increase its stability, and make it an

Overall more capable crawler

mm increased density over stock cover for additional toughness and weight

Fits either the front or back

Specifications:

Width:14.33 mm

Height:24 mm

Weight: 9g

This item is regularly acquired with the above stated item.

9.5G Brass Kmc Machete Wheel Weights, For Axial Scx24

9.5g Brass KMC Machete Wheel Weights, for Axial SCX24

Hot Racing front or rear wheel weights for the stock 1.0in KMC Machete wheels on the Axial SCX24.

Features:

CNC machined strong brass billet

9g each fitted to the wheels to decrease the vehicles center of gravity, increase its stability, improve climbing up, decrease the chance for flipping in reverse, and make for an overall more capable crawler

Friction fit to within KMC Machete wheels. Some CA glue can be used to secure setup

Can be used either in front of back, but if you're just getting one set we recommend utilizing them in the front

Specifications:

Center: 12mm hex

For : AXI31615

Diameter of external : 21.4mm

Diameter of inside : 12mm

Weight: 9.5g/ea

Width: 8mm

The listed below item also pairs actually well with the item being gone over.

Brass Front Steering Knuckle, For Axial Scx24

Brass Front Steering Knuckle, for Axial SCX24

Hot Racing heavy duty brass SCX24 Worm gear Axles guiding knuckles (guiding blocks) for the Axial SCX24 axles. Include weight to your crawler where it requires it - down low.

Features:

CNC machined strong brass

Heavy to include weight to lorry for higher stability and lower CG

Cutouts on knuckle for gain access to to external bearing race for easy bearing removal

Direct replacement for factory plastic guiding knuckles

This item is regularly acquired with the above stated item.

Brass Stock Wheels Hub, 7Mm Hex, For Scx24

Brass Stock Wheels Center, 7mm Hex, for SCX24

Functions:

CNC Machined Solid Brass construction.

You Will Receive:

4 Hex Wheel Hubs

4 2 x 6mm Axle Pins

Requirements:

Assembly onto SCX24.

Specs:

Hex: 7mm

Inner diameter: 4mm

This item is regularly acquired with the above stated item.

Stainless Steel Front Or Rear Axle Skid Plate, For Axial Scx24

Stainless Steel Front or Rear Axle Skid Plate, for Axial SCX24

Hot Racing stainless-steel skid plate for the front or rear axle of the Axial SCX-24. This skid plate is the ultimate rock strike defense. Comes with the following:

- One (1) 6061 Aluminum install

- One (1) skid plate

- Two (2) M1.4 x 12 mm screw

- Two (2) M1.4 X 10 mm Screw

- Two (2) M1.4 x 4 mm Screw

Functions:

Formed from a single sheet of Stainless-steel plate for the ultimate toughness

CNC 6061-T6 aluminum mount.

Designed to decrease obstacle hang ups and improve slide over terrain

Attaches to front or rear axle housing utilizing supplied screws

Specifications:

Width: ~15mm

Thickness: 0.5mm

Weight: 6g