HPI Shock Body Set, Bullet Mt/St (2 Sets)

This is the Shock Body Set (2 Sets)
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored, two total shock bodies.
Plastic building and construction

INCLUDES:
Six parts

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Want an additional excellent product to compliment the above mentioned product?



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System permits connectivity in between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    simply attach desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
CHECK OUT the ENTIRE direction sheet included with battery prior to usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER permit to Discharge below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any method or puncture cells
NEVER put on combustible products or leave unattended throughout
charging
ALWAYS charge in a fireproof area
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of children

Get this product to enhance the one you are reading about.

Silicone O-Ring P-3 Red

This is a Package of Red P-3 Silicone O-Rings for Hobby Use.
These are used in shocks, soaking up vibration, and lots of other uses.

FEATURES:
Silicone construction.

INCLUDES:
5 P3 o-rings.

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Inner diameter: 3mm (0.20")

COMMENTS:
These o-rings are not limited to use only in HPI automobiles.

This is a great enhancement to the product currently being reviewed.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Penny not included)
FEATURES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for lots of applications in all HPI automobiles and trucks

INCLUDES:
(10) Screws

SPECIFICATIONS:
Length: 8mm
Size: 3mm