HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to secure versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

Frequently purchased with the product that you are presently checking out.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Cent not included)
INCLUDES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for numerous applications in all HPI vehicles and trucks

INCLUDES:
(10) Screws

SPECS:
Length: 8mm
Size: 3mm

You will certainly like this thing if you have the thing earlier discussed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connectivity in between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    simply connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Vehicle balancer (TCPP9150)

SPECS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
CHECK OUT the ENTIRE direction sheet included with battery prior to use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER enable to Discharge listed below 2.5V per cell
NEVER dismantle or modify pack circuitry in any way or leak cells
NEVER place on combustible materials or leave unattended throughout
charging
ALWAYS charge in a fire-resistant area
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

Want an additional fantastic product to match the above discussed product?

Flanged Lock Nut, M4, (4Pcs), Bullet St/Mt, Rs4, Venture, Sport

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which require simple elimination and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Here is an additional product that compliments the product being talked about.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECS:
Thread: 3mm (0.118")
Length: 3mm (0.118")