HPI Ball Stud, 4.8X12mm, (10Pcs), Blitz/E-Firestorm/Firestorm 10T

These are the Ball Studs for the HPI Firestorm

FUNCTIONS:
Constructed of steel
Threads into hub carriers and links turnbuckles via ball ends

CONSISTS OF:
10 Ball Studs for the HPI Firestorm

NEEDS:
Threading into hub carriers

Below is an additional item that compliments the item being gone over.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System enables connectivity in between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely attach desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
CHECK OUT the ENTIRE guideline sheet consisted of with battery before usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER allow to Release below 2.5V per cell
NEVER dismantle or modify pack circuitry in any method or puncture cells
NEVER put on flammable products or leave ignored throughout
charging
ALWAYS charge in a fire-resistant area
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of children

Below is an additional item that compliments the item being gone over.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel building

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This item compliments the above gone over item.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Steel building

CONSISTS OF:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Lots of others have gotten this item along with the item that you are presently reading about.

Differential Gear Set, Bullet Mt/St

This is the Diff Gear Set
For the HPI Racing WRI and Bullet Series

FUNCTIONS:
Steel building
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Also fits all three transmissions of the D413 Buggy Kit from Hot Bodies

CONSISTS OF:
Two large bevel gears
4 small bevel gears

COMMENTS:
This differential gear set can be set up on
1/8 WR8 3.0 Ford Feast Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR