APC 10x4.7 Slow Flyer Pusher

This is the APC 10x4.7 Slo-Flyer Pusher Electric Propeller.

FEATURES:
Enemy electric and Park-Flyer type airplane
Pusher propellers molded in the opposite direction from basic
    propellers, they are created for planes with the motor dealing with
    backwards in the rear of the airplane, PUSHING the airplane forward
Lightweight molded nylon building and construction minimizes turning mass for
    greater output and longer life
Reinforcing fibers assist keep real, continuous pitch at any RPM

CONSISTS OF:
APC 10x4.7 Slo-Flyer Pusher Electric Propeller
0.236" (5.9mm) and 0.188" (4.8mm) locating rings
Guideline sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7"

COMMENTS:
Slo-Flyer props cannot be used on glow or gas powered engines

This is a wonderful enhancement to the product currently being reviewed.

10x4.7 Slow Flyer Propeller

This is a 10x4.7 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction minimizes turning mass for
    greater output and longer life.
Reinforcing carbon fibers assist keep real, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7

COMMENTS:
Slo-Flyer props are Not created for Glow engines

You will certainly enjoy this product if you have the product just above pointed out.

Gold Plated Bullet Connector Female 3.5mm (3)

Developed for use with 3 wire Brushless motor systems, this is
the 3.5mm Gold Bullet Connector Female from Great Planes.

FEATURES:
Gold plated
Fits wire diameter approximately 3.5mm

CONSISTS OF:
Three female bullet ports

REQUIRES:
Solder and soldering iron - HCAR0776 and STAR2000

SPECIFICATIONS:
Length: .51" (13mm)
Diameter: .14" (3.5mm) inside (where the wire is soldered to)
Diameter: .17" (4.25mm) outside

COMMENTS:
For the 3.5mm male connector order GPMM3112

Want an additional wonderful product to compliment the above mentioned product?



This is a 17 gram tube of Racers Edge 60/40 Rosin Core Solder. This high quality solder is ideal for all electronic applications.

This is a wonderful enhancement to the product currently being reviewed.

2.5Mm X 6 Socket Head Cap Screws (4/Pkg)

Dubro Socket Head Cap Screws are perfect for locations where a screwdriver won't
reach. They can be tighteded with an allen wrench or ball driver. The screws
can be found in a range of diameters and lengths. This utilizes a 2.5mm balldriver
(BONR1110).

You will certainly enjoy this product if you have the product just above pointed out.

1/8" (3.1Mm) Heat Shrink Tubing (4 Red & 4 Black / Pkg)

This is a set of 1/8" diameter Heat Shrink Tubing from Dubro.

FEATURES:
Developed to shrink approximately 1/2 of its original size
Perfect for insulating electrical splices, covering electrical plugs
and ports

CONSISTS OF:
4 pieces of red heat shrink tubing
4 pieces of black heat shrink tubing

REQUIRES:
Diminish tubing on all sides with heat gun, butane lighter or soldering
iron

SPECIFICATIONS:
Diameter: 1/8" (3mm)
Length: 1-1/2" (38mm)

COMMENTS:
Use a tubing size that is no more than twice the diameter of the
things being covered.